Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
close to the test items, it is necessary to account for the effects of distortion and parallax
when analyzing the film. The acceleration sled facility faces the same problems in
accommodating rearward-facing or side-facing seats in Test 1 as the deceleration sled
facility, and the corrective action is the same for both facilities.
(C) Impact-with-rebound sled facilities. One other type of horizontal test
facility used is the “impact-with-rebound” sled facility. On this facility, the impact takes
place as the moving sled contacts a braking system, which stores the energy of the
impact, and then returns the stored energy back to the sled, causing it to rebound in the
opposite direction. This facility has an advantage over acceleration or deceleration
facilities in that only one-half of the required velocity for the impact would need to be
generated by the facility (assuming 100 percent efficiency). Thus the track length can
be shortened, and the method of generating velocity is simplified. The disadvantages of
this facility combine the problems mentioned for both acceleration facilities and
deceleration facilities. Since one of the reasons for this type of facility is to allow short
track length to be used, it may be difficult to obtain sufficiently low acceleration just
before or after the impact pulse to resolve data error problems caused by significant
pre-impact and post-impact accelerations.
(D) Drop towers. Vertical test facilities can include both drop towers
(decelerators) and vertical accelerators. Vertical accelerators, which can produce a
longer duration/displacement impact pulse, may not be available. However, drop
towers are one of the easiest facilities to build and operate and are frequently used.
(1) Acceleration phase. In these facilities, the pull of earth’s gravity is
used to accelerate the sled or guided test fixture and test article to specified impact
velocity to avoid the use of a complex mechanical accelerating system. Reproducing
the required impact pulse may require extensive development tests for the facility.
Unfortunately, these facilities are more difficult to use for conducting Test 2, particularly
for typical forward-facing seats.
(2) Test article. In preparing for (longitudinal) Test 2, the seat should be
installed at an angle according to the standards such that the ATD’s tend to fall from the
seat due to gravity. The restraint system being tested cannot hold the ATD against the
seat unless tightened excessively and will not usually locate the head, arms, or legs in
their proper position relative to the seat. Design and fabrication of an auxiliary
“break-away” ATD positioning restraint system just for this test are usually a complex
task. The auxiliary restraint should not only position the ATD against the seat (including
maintaining proper seat cushion deflection) during the pre-release condition of 1 g, it
should also maintain the ATD in that proper position during the free fall to impact
velocity when the system is exposed to zero g, and then it should release the ATD in a
manner that does not interfere with the ATD response to impact. The usual sequence
of 1 g/0 g impact, without the possibility of a useful “coast” phase, as done in horizontal
facilities, causes shifts in initial conditions for the test impact pulse that can affect the
response to the impact. The significance of this undesired movement will depend on
Page C - 50
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.