FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-49

PDF page 199 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 199
AC 27-1B · C-49Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/12/03                                        AC 27-1B, Chg 1

test should also be reviewed to make certain that the ATD’s used in the test and the test
articles were all in their proper position prior to the test impact pulse.

               (2) Orientation of test article. The horizontal test facility readily
accommodates forward-facing seats in both tests discussed in this guidance, but
problems can exist in positioning the test ATD in Test 1 if the seat is a rear or side-
facing seat. In these cases, the ATD’s tend to fall out of the seat due to the force of
gravity and must be restrained in place using breakaway tape, cords, or strings. Since
each installation will present its own problems, there is no simple, generally applicable,
guidance. Attention should be given to positioning the ATD against the seat back and
to proper positioning of the ATD’s arms and legs.  It will probably be necessary to build
special supports for a breakaway restraint so that the restraint will not interfere with the
function of the seat and occupant restraint system during the test. Photos of the test
from “side of track cameras” should be reviewed to make sure that the breakaway
restraint did break (or become slack) in a manner that did not unduly influence the
motion of the ATD or the test articles during the test.

              (B) Acceleration sled facilities. Acceleration sled facilities, usually based
on the Hydraulically Controlled Gas Energized (HYGE) accelerator device, provide the
impact test pulse as a controlled acceleration at the beginning of the test. The test item
and the ATD are installed facing in the opposite direction from the velocity vector,
opposite from the direction used on a deceleration facility, to account for the change in
direction of the impact. There should be no problem with the ATD or the test items
being out of position due to pre-impact sled acceleration, since there is no sled
movement prior to the impact test pulse. Because of this characteristic the applicant
may prefer this type of a facility.

               (1) Test pulse. After the impact test pulse, when the sled is moving at the
maximum test velocity, stop the sled safely. Most of the facilities of this design have
limited track length available for deceleration, so that the deceleration levels can be
relatively high and deceleration may begin immediately after the impact test pulse.
Since the maximum response of the system usually follows (in time) the impact test
pulse, any sled deceleration, which takes place during that response will affect the
response and change the test results. The magnitude of change depends on the
system being tested, so that no general “correction factor” can be specified. The effect
can be minimized if the sled is allowed to coast, without significant deceleration, until
the response is complete.

               (2) Test results.  If the seat or restraint system experiences a structural
failure during the test pulse, the post impact deceleration can increase the damage and
perhaps result in failures of unrelated components. This will complicate the
determination of the initial failure mode and make product improvement more difficult.
One other consideration is that the photometry film coverage of the response to impact
test pulse must be accomplished when the sled is moving at near maximum velocity.
Onboard cameras or a series of trackside cameras are usually used to provide film
coverage of the test. Since onboard cameras frequently use a wide-angle lens placed


                                                          Page C - 49

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →