Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(2) Test facilities. A test proposal is prepared for certification authority approval
and should reflect the capability of the facility. It should be noted that a number of test
facilities could be used to accomplish dynamic testing. Test facilities can be grouped
into categories based on the method they use to generate the impact pulse (i.e.,
accelerators, decelerators, or impact with rebound) and whether the facility is a
horizontal (sled) design or a vertical (drop tower) arrangement. As in all certification
compliance tests, a test proposal, which may refer to certain specific or generic test
equipment, is approved prior to testing. The test may be conducted anywhere, within
certain availability or mutually convenient constraints, as long as the test is conducted in
accordance with the approved test plan and properly witnessed.
(i) Facility Characteristics or Features. Each of the facilities has
characteristics that may have advantages or disadvantages with regard to the dynamic
tests discussed in this guidance. One concern is the rapid sequence of acceleration
and deceleration that must take place in the tests. In a landing impact, the acceleration
phase (flight) is gradual and usually well separated in time from the deceleration (crash
impact) phase. In a test, the deceleration usually closely follows the acceleration.
When assessing the use of a facility for the specific test procedures outlined in the
recommendations, it is necessary to assess the possible consequences of this rapid
sequence of acceleration and deceleration on the test articles and ATD. The standard
accommodates the different facilities that are or may be available for the applicant’s
use. That is, the standards dictate the peak acceleration with a tolerance as stated in
this AC. The “decay” in deceleration with respect to time is not dictated, thereby
allowing for the different test facility equipment characteristics.
(A) Deceleration sled facilities. In an aircraft crash, the impact takes
place as a deceleration, so loads are applied more naturally in test facilities that create
the test impact pulse as a deceleration. Since it is simpler to design test facilities to
extract energy in a controlled manner than to impart energy in a controlled manner,
several different deceleration sled facilities can be found. The deceleration sled facility
at the FAA’s Civil Aeromedical Institute (CAMI) was referred to in developing the test
procedures discussed in this and similar AC’s related to airplanes.
(1) The Acceleration Phase. Sufficient velocity for the test impact pulse
acquired in this phase can distort the test results if the acceleration is so high that the
test articles or ATD are moved from their intended pre-test position. This inability to
control the initial or onset conditions of the test would directly affect the test results.
This can be avoided by using a lower acceleration for a relatively long duration and by
providing a coast phase (in which the acceleration or deceleration is nearly zero) prior to
the impact. This allows any dynamic oscillation in the test articles or the ATD that might
be caused by the acceleration to decay. To guard against errors in data caused by
pre-impact accelerations, data from the electronic test measurements (accelerations,
loads) should be reviewed for the time period just before the test impact pulse to make
sure all measurements are at the baseline (zero) level. Photometry film taken of the
Page C - 48
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.