Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(4) Seat assemblies that provide an energy absorbing system between a
seat “bucket or pan” and a seat frame attached to the floor may not perform properly for
a pre-loaded seat frame attached to the floor or sidewall. Deformation of the seat frame
may cause the energy absorbers to receive unanticipated loads or cause excessive
friction in the guides between the seat bucket and seat frame to lock the energy
absorber in place.
(5) Restraint system anchorages attached to the airframe structure may
be significantly displaced relative to the seat if the seat deforms during the test, and that
displacement may inhibit proper performance of the seat/restraint system. This is
especially critical for the necessary vertical stroking or displacement.
(B) Floor Deformation. The pitch and roll displacement is intended to
evaluate the track or stud and leg fitting joint (axis) tolerance to angular misalignment
and not necessarily axis translational displacement.
(1) For the typical aircraft seat. For a multiple or single person seat, with
four seat legs mounted in the airframe on two parallel tracks, the floor deformation test
fixture may consist of two parallel beams, a “pitch beam” which pivots about a lateral (y)
axis, and a “roll beam” which pivots about a longitudinal (x) axis. The beams can be
made of any fairly rigid structural form, box, I-beam, channel, or other appropriate cross
section. The pitch beam should be capable of rotating in the x-z plane up to +/- 10°
relative to the longitudinal (x) axis. The roll beam should be capable of a +/- 10° roll
about the axis of the seat attachment/fitting joint (centerline of floor track or fittings).
(See Figure 27.562-2 for a schematic of an installation.) A means should be provided to
fasten the beams in the deformed positions.
(2) Seat and floor interface. The beams should have provision for
installing floor tracks or other attachment fittings on their upper surface in a manner that
does not alter the above-floor strength of the track or fitting. The track or other
attachment fittings should be representative (in above-floor configuration shape and
strength) of those used in the rotorcraft. Structural elements below the surface of the
floor that are not considered part of the floor track or fitting may be omitted in the
installation. The seat having four legs should then be installed on the beams so that the
rear seat leg attachment point is near the pitch beam axis of rotation, and the seat
positioning pins or locks are fastened in the same manner as specified in the test
proposal and as would be used in the rotorcraft, including the adjustment of “anti-rattle”
mechanisms, if employed.
(3) Test set-up. The remainder of the test preparations would then be
completed (ATD installation and positioning, instrumentation installation, adjustment
and calibration, camera checks, etc.). The “floor deformation” would be induced as the
final action before the test is accomplished. The roll beam should first be rotated 10°
and locked in place, and then the pitch beam should be rotated 10° and locked in place.
The direction of rotation would be selected to produce the most critical loading condition
on the seat and floor track or fitting. If the seat is fairly flexible, it may be possible to
Page C - 52
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.