FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-45

PDF page 195 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 195
AC 27-1B · C-45Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

3/31/2014                                       AC 27-1B, Chg 4

unique interior arrangements. The seat, restraint system, and related interior system
should be designed for the range of occupants and environments for which it is
expected to perform, not just for the dynamic test conditions described in this guidance.

                  (i)   Occupant size. The dynamic tests are conducted with a specific,
acceptable, standard anthropomorphic test dummy (ATD) representing a 50th percentile
male occupant. Energy absorbing systems, restraint system loads and anchorage
locations, seat adjustments, seat pitch (for multiple seat rows), head strike envelopes,
etc., are typical factors directly influenced by occupant size.

                   (ii)   Seat position and location. The tests should be sufficient to represent
the range of performance expected of a seat and restraint system. A seat, especially an
adjustable flight crew seat, should be qualified for those positions approved for take-off
and landing. As with static test procedures the seat is also tested to the most critical
condition for the dynamic tests. For an adjustable flight crew seat, as an example, the
full-up position and longitudinal impact case are expected to be the critical condition.
But these dynamic tests and occupant injury assessment provide a systems approach
to qualification.  It is therefore necessary to test adjustable seats at the design position
for the ATD. Two tests would be required to demonstrate compliance with the strength
standards and with the occupant injury criteria. Alternatively adjusting the flight crew
seat to its highest position with the interior features, such as an instrument panel shield,
raised to maintain the proper perspective or relation to the ATD, is considered an
acceptable test procedure for demonstrating compliance with the structural and
occupant injury requirements for the seat and its location in a particular cockpit
arrangement.

                    (iii)   Test conditions. Only two minimum impact tests are described in the
dynamic test procedures discussed in this guidance. These procedures address the
tests needed to demonstrate compliance for a typical seat and restraint system
installation. Additional tests may be necessary to demonstrate compliance for other
types or variations of seat and restraint system installations. For example, while only
one lateral load direction is specified in the tests, the system should perform properly
when similarly loaded from either side.

               (iv)   Floor deformation. The test procedures require evaluating the effect
of certain sidewall or floor deformation. The seat and its attachments and the restraint
system should also perform properly if no floor deformation is present.

              (v)  Head impact. Should such contact occur, head impact with a seat
back or the interior of the rotorcraft is evaluated by using a Head Injury Criterion (HIC),
which can be measured directly in the tests discussed in this guidance or in
supplementary tests of the interior. The design of the interior should protect the head
from serious injury throughout the head strike envelope, not just along the head strike
paths demonstrated in the test conditions discussed in this guidance.




                                                          Page C - 45

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →