FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-46

PDF page 196 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 196
AC 27-1B · C-46Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 4                                                       3/31/2014

               (vi)  Emergency egress. Standards for emergency evacuation of the
rotorcraft are contained in FAR Part 27. The objective is to allow each occupant to
leave the seat and rapidly evacuate the rotorcraft using an exit on either side of the
rotorcraft.

      c. Dynamic Test Methods and Facilities.

         (1) General. A minimum of two dynamic tests are used to assess the
performance of the rotorcraft seat, restraint system, and related interior system. The
seat, the restraint, and the nearby interior all function together as a system to protect
the occupant during emergency landing. The specific test conditions are shown in
Figure AC 27.562-1. Explanations of the test conditions are as follows:

                  (i)   Test 1. The test determines the protection provided when the impact
environment is such that the resulting predominant impact load component (vertical) is
directed along the spinal column of the occupant in combination with a horizontal
(longitudinal) component. Protection against spinal injury is important and it may be
necessary to provide energy absorbing (load limiting) or attenuation capability in the
seat system in order to comply with the human injury criteria specified in § 27.562 (c)(7).

                   (ii)   Test 2. The test determines the protection provided in an impact
where the predominant impact load component is in the longitudinal direction in
combination with a lateral component. Evaluation of head injury protection is important
in this test if the head could strike some interior portion of the rotorcraft or a forward
seat. Chest or spinal column injury, which might result from the upper torso restraint, is
also evaluated in this test.

                    (iii)   Tests 1 and 2. These test conditions are also significant for the
structural strength of the system. Both tests should be used to assess submarining
(where the seat belt slips above the ATD pelvis) and rollout of the upper torso restraint
system particularly with single, diagonal torso restraint belts. Since external crash
forces frequently cause significant structural deformation, simulated floor deformation is
specified for the tests to prove the seat design can accommodate the relative
deformation between the seat and the floor or sidewall and still function without
imposing excessive loads on the seat, the attachment fittings, or floor tracks.





Page C - 46

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →