Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
§ 27.561(d) load factors only apply to the rotorcraft airframe surrounding the underfloor
fuel tanks and their installation for the same reasons. These two sets of load factors are
not additive. They are applied separately (as design ultimate load factors) to the
portions of the rotorcraft to which they are specified to apply. The application of the
§ 27.561(d) load factors is described as follows. The loads generated by § 27.561(d)
are intended to be applied to the airframe structure surrounding the fuel cell to ensure
that the entire airframe structure provides the appropriate level of crash resistance (i.e.,
stiffness, crushability, crushing rate, energy absorption capability, etc.) and to ensure
that the airframe structure’s failure modes (e.g., buckling, creation of sharp edges,
structural spears, etc.) are such that fuel cell rupture (and the resultant post crash fire
potential) is mitigated to the maximum practicable extent in a otherwise survivable
emergency landing. Each fuel cell (and major fuel cell component) creates an applied
load on the airframe in an emergency landing condition. These loads are determined by
multiplying the worst case mass of the fuel cell (i.e., a full fuel cell) by the load factors of
§ 27.561(d). These loads are then applied (utilizing the appropriate design load paths)
to the airframe structure surrounding the fuel cell to help design the structure for optimal
crash resistance. Added stiffness effects for both a full and less than full fuel cell should
be considered in the design process. A significantly less than full fuel cell will typically
not have any significant stiffness effects, since in a less than full condition the fuel cell
cannot typically transfer load hydraulically.
AC 27.561C. § 27.561 (Amendment 27-32) EMERGENCY LANDING
CONDITIONS - GENERAL.
a. Explanation. Amendment 27-32 adds a new rearward emergency load factor of
1.5g to both §§ 27.561(b)(3)(v) and 27.561(c)(5). The addition of the 1.5g rearward
load factor in § 27.561(b)(3)(v) is to provide an aft ultimate load condition for
substantiation of the restraints required for retention of both occupants and significant
items of mass inside the cabin that could otherwise come loose and cause injuries in an
emergency landing. The addition of the 1.5g rearward load factor to § 27.561(c)(5) is to
provide an aft ultimate load condition for substantiation of the support structure for
retention of significant items of mass above and forward of the occupied volume(s) of
the rotorcraft that could otherwise come loose and injure an occupant in an emergency
landing. Amendment 27-32 also increases the forward, sideward, and downward
emergency load factors of § 27.561(c)(2), (c)(3), and (c)(4), respectively; for retention of
items of mass above and behind the occupied volume(s) that could otherwise come
loose and injure an occupant in an emergency landing.
b. Procedures. The procedures in sections 27.561, 27.561A, and 27.561B of this
AC continue to apply except the newly specified load factors must be used. A list of the
significant items of mass to be considered should be compiled by the applicant and
approved by the certifying authority.
Note: For doors and emergency exit design, when applicable, the rearward load
factor to consider is in § 27.561(b)(3)(v).
Page C - 43
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.