Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
b. Procedures. The procedures in section 27.561 of this AC continue to apply
except the new load factors of § 27.561 should be used. Penetration of any items of
mass into the cabin or occupied areas should be prevented.
AC 27.561B. § 27.561 (Amendment 27-30) EMERGENCY LANDING
CONDITIONS - GENERAL.
a. Explanation.
(1) Amendment 27-30 adds paragraph (d), which lists specific load factors for the
fuselage structure in the area of internal fuel tanks located below the passenger floor
level. For other locations, the fuselage structure is to be designed to resist crash impact
loads prescribed in § 27.561(b)(3) for fuel tanks located within the cabin area; or
§ 27.561(c) for fuel tanks located behind or above the occupant area. These load
factors are provided to prevent crash induced fuel tank ballistic hazards to occupants
and to also protect the fuel tank from rupture as prescribed. The landing gear must be
retracted if the rotorcraft is equipped with retractable gear.
(2) Section 27.952(b) provides specific load factors for the fuel tanks which are
identical to the load factors stated in § 27.561. Section 27.952 of this AC provides
information and guidance for § 27.952 and may be used in conjunction with this section.
(3) Door and exit protection. The minor crash conditions contained in
§ 27.561(d) should also be considered in designing doors and exits (§ 27.807(b)(4)). If
any item of mass installed in the cabin can possibly interact with the fuselage and
cause higher deformation, then § 27.561 (b) (3) loads factors should be applied to
design of doors and emergency exits.
b. Procedures. The procedures in sections 27.561 and 27.561A of this AC continue
to apply except new load factors are established for fuel tanks located below the
passenger floor level. Each fuel tank and its installation are subject to the loads stated
in the standard. The load factors are determined by the fuel tank location.
(1) The crash impact load factors for the airframe structure surrounding the
underfloor fuel tanks are specified in § 27.561(d). The fuselage structure must be
designed to resist the specified crash impact loads and to help protect the fuel tank from
rupture. If equipped with retractable landing gear, the effects of the landing gear on fuel
system rupture should be considered in both the retracted and unretracted
configurations for fuel cell hazard purposes, only, in accordance with section 27.952 of
this AC.
(2) Section 27.952(b) (see section 27.952 of this AC) specifies the design load
factors for crash resistant fuel systems in an otherwise survivable impact. This section
relates to § 27.561(d) as follows. The § 27.952 load factors are for the fuel tanks, other
significant mass items in the fuel system, and their attachment to the rotorcraft airframe
for both occupant survivability and retention of fuel in a survivable impact; whereas, the
Page C - 42
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.