FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-33

PDF page 183 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 183
AC 27-1B · C-33Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


         (5) Braked roll conditions are specified for the level landing attitudes.

         (6) Rear wheel turning loads are also specified for swiveling and locked tail
wheels.

         (7) Taxiway condition loads for the landing gear and rotorcraft are those that
“occur when the rotorcraft is taxied over the roughest ground that may reasonably be
expected in normal operation.” The aircraft design load factors should not be exceeded
during the evaluation. Section 27.235 contains an identical standard that applies to all
types of wheel landing gear.

     b. Procedures.

         (1) The specified loading conditions are to be used in load derivations.

         (2) The critical center of gravity condition is used for each gear and gear
support structure.

                  (i)   The forward center of gravity condition with the tail gear clear will
normally be critical for the forward gear and gear supports.

                   (ii)   The aft center of gravity condition with the tail gear clear should be
checked for criticality of security of large mass items located forward of the center of
gravity. Vertical and angular accelerations are additive under this landing condition.

                    (iii)  The aft center of gravity condition with each gear contacting the
ground simultaneously will generally design tail gear elements critical for vertical loads.
The other conditions are generally less severe but must be proven.

         (3) For tail-down landing procedures use § 27.481. The reference to
“extremely remote” in § 29.497(d)(2) predates current §§ 25.1309, 29.1309, and
AC 25.1309.1. This phrase has been used to require consideration of nose-up landings
unless features of design are present which prevent nose-up landings or where such
landings are unlikely during the life of the rotorcraft. (See paragraph AC 27.481.)

         (4) Use § 27.483 for one-wheel landing procedures, paragraph AC 27.483.

         (5) Use § 27.485 procedures for side load conditions, paragraph AC 27.485.

         (6) Use § 27.493 procedures for braked roll conditions, paragraph AC 27.493.

         (7) For rear wheel turning loads, swiveling of tail landing gears is allowed as in
basic side load conditions. The side load is applied at the axle or, if the wheel is locked,
the load is applied at ground contact. Rear wheels are loaded with the critical vertical
static load in conjunction with an equal side load to substantiate the tail gear.


                                                          Page C - 33

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →