FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-32

PDF page 182 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 182
AC 27-1B · C-32Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


AC 27.493  § 27.493 BRAKED ROLL CONDITIONS.

     a. Explanation. This section provides two loading conditions for ground braking
operations. Specific vertical loads in conjunction with drag loads (due to braking) are to
be considered. The limit vertical load factor is 1.33 for condition of all wheels in contact
with the ground and 1.0 for condition of aft wheels only in contact with the ground and
nose wheel clear. The drag load on wheels with brakes is 0.8 times the vertical load or
the drag load value based on limiting brake torque, whichever is less. The drag load
value for limiting brake torque may be that determined in the performance testing to
TSO C26 or equivalent, as required.

     b. Procedures. The braking loads are calculated from the specified criteria with
the shock absorbers in their static (normal) positions and with the drag loads applied at
the ground contact point. Structural substantiation of the affected structure may be
accomplished by test or analysis.  If tests are used, the wheel and tire assembly is
commonly replaced with a test fixture so the limit loads and static deflections specified
can be more accurately controlled. The test specimen should be complete enough to
ensure that the landing gear structure and the attach and backup structure are
adequately substantiated.

AC 27.497  § 27.497 GROUND LOADING CONDITIONS: LANDING GEAR WITH
           TAIL WHEELS.

     a. Explanation. This section provides the loading conditions for landing gear
designs with tail wheels.

         (1) Level landings are to consider the following:

                  (i)     All wheels (main and tail) contacting the ground simultaneously, as
well as only forward main wheels contacting the ground.

                   (ii)  Maximum design vertical loads applied alone.

                    (iii)  The maximum design vertical loads combined with a drag load of at
least 25 percent of the vertical loads for both conditions.

(2)  Nose-up landings with only the rear wheel or wheels initially contacting the ground
must be considered unless shown to be extremely remote.

         (3) Level landings on one forward wheel only are to be considered. Drag loads
are not required.

         (4) Side load conditions are imposed on the main wheels and tail wheels for
level landing attitudes. Criteria for full swiveling and locked tail wheels are included in
this standard.


Page C - 32

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →