Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(2) The tail-down landing condition may be the critical condition for both landing
load factor and for energy absorption by the main gear. Section 27.725 requires that
“each landing gear must be tested in the attitude simulating the landing condition that is
most critical.” Where questions exist as to the critical attitude, both level landing and
tail-down landing attitudes should be used in drop tests required by § 27.725.
AC 27.483 § 27.483 ONE-WHEEL LANDING CONDITIONS.
a. Explanation. This section gives the condition to be used for one-wheel landing
conditions. Only the vertical load condition of § 27.479(b)(1) is required.
b. Procedures. The one-wheel landing condition is generally critical for the
landing gear-to-fuselage attachments and the landing gear elements between the
attachments. Unbalanced external loads are reacted by rotorcraft inertia.
AC 27.485 § 27.485 LATERAL DRIFT LANDING CONDITIONS.
a. Explanation.
(1) This section provides the loading conditions which impose side (and
vertical) loads on the landing gear. A level landing attitude is specified. Two main
conditions required are-
(i) Only the aft wheels in contact with the ground; and
(ii) All wheels contacting the ground simultaneously.
(2) Loads. The vertical loads to be applied with the side loads are specified as
“one-half of the maximum ground reactions of § 27.479(b)(1).” These vertical loads are
the level landing loads considering both contact and noncontact with the ground by the
forward wheels.
(i) One side load condition is specified as “0.8 times the vertical reaction
acting inward on one side and 0.6 times the vertical reaction acting outward on the other
side” when only the aft wheels contact the ground.
(ii) The other side load condition (for all wheels contacting the ground)
specifies the 80 percent inward/60 percent outward distribution for the aft wheels and
0.8 times (80 percent) the vertical reaction for the forward wheels.
b. Procedures. The loading conditions, as specified, are applied to the landing
gear and attaching structure. The loads are applied at the ground contact point, except
for full swiveling gear which has the load applied at the center of the axle. In other
words, full swiveling gear is considered to have swiveled to a static position under the
side load before the design vertical and side loads are achieved. The rotorcraft as well
as the landing gear itself will be substantiated for these side load conditions.
Page C - 31
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.