Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
NOTE: The method is valid for aspect ratios of 5 through 12 and for rectangular
planforms such as used on rotorcraft, other planforms may be acceptable as prescribed
in the TM.
(ii) The chordwise distribution appropriate for the aerodynamic shape or a
conservative distribution should be used.
(iii) The flight load survey conducted under § 27.571 may be used to
confirm design parameters and possible load distribution data. On controllable
surfaces, the pitching moment (control loads) may be measured for fatigue
substantiation of the control system. The control stabilizing surfaces may be subject to
loads measurement and possible fatigue tests for fatigue substantiation also.
(3) Proof of the structure for the required loads is specified in §§ 27.301,
27.303, 27.305, and 27.307. Tests or analysis may be used as prescribed. If analysis
is used, fitting factors and other appropriate factors prescribed by the rules of
§§ 27.625, 27.621, and 27.623 will be required in the analysis.
AC 27.413A. § 27.413 (Amendment 27-27) STABILIZING AND CONTROL
SURFACES.
a. Explanation. Amendment 27-27 removed this section since the requirements
are adequately addressed in §§ 27.337, 27.339, and 27.341.
b. Procedures. The policy material pertaining to this section is retained as
supplemental information especially as reference material for paragraph AC 27.341
(§ 27.341).
AC 27.427. § 27.427 (Amendment 27-27) UNSYMMETRICAL LOADS.
a. Explanation. Amendment 27-26 added the standard and Amendment 27-27
amended it. Minimum unsymmetrical design loads are specified for horizontal tail
surfaces and also vertical tail surfaces whenever they support the horizontal tail
surfaces.
(1) Loads are derived by rational analysis, or for earlier certification bases, the
prescribed empirical loads of § 27.413 may be used. Section 27.413 was removed by
Amendment 27-27 since the requirements are adequately addressed in §§ 27.337,
27.339, and 27.341.
(2) Rational loads, appropriate for the aerodynamic surfaces, should be
distributed according to the standard.
(3) When vertical tail surfaces support the horizontal tail surfaces, the vertical
tail surfaces and supporting surfaces are required to support the critical combination of
vertical and horizontal surface loads.
Page C - 24
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.