FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-23

PDF page 173 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 173
AC 27-1B · C-23Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (2) Paragraph (b) requires load distributions that closely simulate actual
pressure distributions. Both spanwise and chordwise distributions are intended.

         (3) These surfaces are used for stability and control thereby hopefully
extending the CG range and increasing the airspeed of modern designs.

         (4) To “closely simulate actual pressure condition” on the surfaces,
unsymmetrical loads are also required on horizontal surfaces. An arbitrary distribution,
if conservative, may be used.

         (5) It is noted § 27.571 requires fatigue substantiation of the flight structure
which will include control and stabilizing surfaces.

         (6) If the surface is controllable, a proof and operation test of the surface
control system is required by §§ 27.681 and 27.683.

     b. Procedures. Modern rotorcraft designs have generally employed a fixed or a
wholly movable, not split or divided, stabilizing or control surface.

         (1) Design Loads.

                  (i)    Limit loads of 15 pounds per square foot will apply up to
approximately a 90-knot design airspeed. Above a 90-knot design airspeed (1.11VNE),
the coefficient (CN = 0.55) imposes higher limit loads on the surface. The coefficient CN
is assumed normal to the chordline of the section.

                   (ii)    In addition, combined maneuvering and vertical up or down gust loads
may impose the highest limit loads on the control surfaces of rotorcraft. This is
attributed to the change in angle of attack and change in resultant airspeed.

                    (iii)  The applicant may choose to derive the limit loads using maximum
aerodynamic coefficients for the surface under consideration at the maximum design
airspeed combined with a 17.8-knot gust. This would be acceptable provided these
design loads exceed the minimum loads derived from a CN = 0.55 at design airspeed or
exceed 15 pounds per square foot load on the surface.

         (2) The load distribution on the surface should closely simulate actual pressure
distributions.

                  (i)   The spanwise load may be rectangular, or other acceptable
conservative distributions may be used. The method developed by O. Schrenk in
NACA TM 948, 1940, is an acceptable method for approximation of spanwise
distribution.





                                                          Page C - 23

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →