FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-22

PDF page 172 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 172
AC 27-1B · C-22Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

means of deriving the rotorcraft kinetic energy that shall be absorbed by the guard. This
method is noted here for convenience.

                  (i)   The tail rotor guard shall be able to absorb the kinetic energy of the
rotorcraft in its most unfavorable CG position in the tail-down landing attitude. The
kinetic energy that the tail rotor guard should be capable of absorbing may be
determined by the following:

             WVS 2            KY 2
      KE  =        X
                2g             (KY2 + 1B 2)


where--     VS = vertical speed ft/sec, derived from § 27.725(a)
           KY = pitching radius of gyration - ft from pitching axis
            1B = distance from most critical CG location to the guard
                    or bumper contact point - ft
       W = gross weight less rotor lift from § 27.473(a) - lbs
           g = 32.2 ft/sec2

                   (ii)   Other, more recent, analytical techniques (most utilizing computer
programs) may, of course, be used rather than the ANC-2a means after proper
substantiation for applicability and validity.

                    (iii)  The tail rotor guard should not fail when the limit and ultimate load,
which is derived from a combination of the limit kinetic energy and the guard resulting
limit deflection required to dissipate the energy, is imposed on the guard and the
rotorcraft tail (see § 27.305).

         (3) Substantiation of the guard, skid, or bumper for the design loads derived
may be accomplished by test or analysis as stated in § 27.307(a).

         (4) Several rotorcraft tail rotor guards are installed solely for the protection of
ground personnel from the rotating tail rotor. For guards installed for this purpose, the
applicant should use prudent and reasonable design loads and features. Such guards
should not present a hazard to the rotorcraft because of its design features.

AC 27.413.  § 27.413 STABILIZING AND CONTROL SURFACES.

     a. Explanation. Minimum design loads are specified for stabilizing as well as
control surfaces.

         (1) Paragraph (a) of the rule requires application of minimum empirical design
loads, application of critical maneuvering loads, and application of critical maneuvering
loads combined with vertical gust loads (30 feet per second or 17.8 knots per § 27.341).



Page C - 22

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →