FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-21

PDF page 171 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 171
AC 27-1B · C-21Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (3) The derivation of the loads and conditions is too extensive to include here.
Additional information can be found in the U.S. Army Material Command Report
AMCP 706-201, “Engineering Design Handbook: Helicopter Engineering, Part One,
Preliminary Design.”

AC 27.403A.    § 27.403 (Amendment 27-27) AUXILIARY ROTOR ATTACHMENT
            STRUCTURE.

     a. Explanation. Amendment 27-27 removed this section since the requirements
are adequately addressed in §§ 27.337, 27.339, 27.341.

     b. Procedures. The policy material pertaining to this section is retained as
supplemental information.

AC 27.411.  § 27.411 GROUND CLEARANCE: TAIL ROTOR GUARD.

     a. Explanation.

         (1) The rule requires specific protection to prevent the tail rotor from contacting
the landing surface during a normal landing if it is possible that the tail rotor will contact
the surface. The rule states that it must be impossible for the tail rotor to contact the
surface during a normal landing.

         (2) If a guard is required, the guard and its supporting structure must withstand
suitable design loads.

         (3) Section 27.501(c)(1) contains skid landing gear drag requirements that may
be applied to the guard design loads.

     b. Procedures.

         (1) The applicant may submit sketches or drawings showing probable
clearance with typical level landing surfaces during normal landings. Typical attitudes
such as nose-high autorotation, or autorotation with power-on landing, or other possible
tail-low attitudes should be investigated.  If the drawings or sketches reveal that it is not
likely the tail rotor will contact the landing surface, this minimum clearance with the
landing surface may be confirmed during official FAA/AUTHORITY flight tests, such as
HV and landing tests. The clearance may be confirmed by having a frangible device of
suitable length (i.e., a balsa wood dowel) extending beyond the guard and attached to
the tail rotor guard or other appropriate fuselage part.  If the device is not damaged,
broken, or no contact is made with the surface, compliance has been demonstrated.

         (2) If it is possible for the tail rotor guard to contact the landing surface, suitable
design loads must be established for the guard. ANC-2a dated March 1948, “ANC
Bulletin Ground Loads,” paragraph 6.4, entitled “Tail Bumper Criteria,” is an acceptable



                                                          Page C - 21

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →