FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-25

PDF page 175 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 175
AC 27-1B · C-25Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B


     b. Procedures. Two basic loading conditions are required by § 27.427 for each of
the two basic empennage configurations.

         (1) Horizontal surfaces supported by the tail boom or fuselage. Structural
substantiation should be provided for all six combinations shown in figure AC 27.427-1.
All of these empirical loading distributions should be used unless rational analysis
shows one or more of each set of conditions to be non-critical or equal or more realistic
distributions are substantiated. Rectangular spanwise air load distribution should be
used unless more rational distribution is substantiated.  If end plates are used, the air
loads should be distributed accordingly.

                  (i)    First unsymmetrical loading condition:

              (A) 100 percent of the flight load is applied to one side of the plane of
symmetry; and 0 percent of the flight load is applied to the other side of the plane of
symmetry.

              (B) For surfaces with end plates or other similar devices, the load
distribution will be changed accordingly.

                   (ii)   Second unsymmetrical loading condition:

50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry
acting down.

         (2) Horizontal surfaces supported by a vertical surface. Structural
substantiation should be provided for all six combinations shown in figure AC 27.427-2.
All of these empirical loading distributions should be used unless rational analysis
shows one or more of each set of conditions to be non-critical or equal or more realistic
distributions are substantiated. Rectangular spanwise air load distribution should be
used unless more rational distribution is substantiated.  If end plates are used, the air
loads should be distributed accordingly.

                  (i)    First unsymmetrical loading condition:

100 percent of the flight load is applied to one side of the plane of symmetry; and
0 percent of the flight load is applied to the other side of the plane of symmetry.

                   (ii)   Second unsymmetrical loading condition:

50 percent of the flight load is applied to one side of the plane of symmetry acting up;
and 50 percent of the flight load is applied to the other side of the plane of symmetry
acting down.



                                                          Page C - 25

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →