FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-19

PDF page 169 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 169
AC 27-1B · C-19Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

that may increase the operating stress levels. Blade weight and strength should be
optimized. Even though a structural strength analysis for the blade design loads is
required, a flight load survey and fatigue analysis are also required by § 27.571.

         (3) Section 27.1509 defines the design rotor speed as that providing a
5 percent margin beyond the rotor operating speed limits.

     b. Procedures.

         (1) The endurance tests prescribed by §§ 27.923 and 27.927 require achieving
certain speeds, power, and control displacement for the auxiliary (tail) rotor as well as
the main rotor. The parts must be serviceable at the conclusion of the tests.

         (2) Structural substantiation of the auxiliary (tail) rotor is required to ensure
integrity for the minimum and maximum design rotor speeds and the maximum design
rotor thrust in the positive and negative direction. Thrust capability of the rotor should
offset the main rotor torque at maximum power as required by § 27.927(b).

                  (i)   The maximum and minimum operating rotor speed, power-off, is
95 percent of the maximum design speed and 105 percent of the minimum design
speed, respectively.

                   (ii)   The rotor operating speed limits shown during the official
FAA/AUTHORITY flight tests must include the noted 5 percent margin with respect to
the design speeds.

                    (iii)  The auxiliary rotor generally has a positive and negative pitch limit that
ensures adequate directional control throughout the operating range of the rotorcraft.
The power-off rotor speed limits are generally broader than the power-on rotor speed
limits because of the required autorotational rotor speed characteristics. Thus, the
auxiliary rotor design conditions concern the maximum and minimum design rotor
speeds in conjunction with the maximum positive or negative pitch thrust, as
appropriate. Thrust capability and precone angle of the rotor, if any, will significantly
influence the rotor design loads. The variations in rotor design features and an example
of substantiation would be too lengthy to include here. However, ANC-9, “Aircraft
Propeller Handbook” contains principles that may be applied to tail rotor designs. Tail
rotors may be considered a special propeller design.

               (iv)  Bearings are generally used in the tail rotor installation to allow
flapping and feathering motion of the blades. The bearing manufacturer’s ratings of
these bearings must not be exceeded. Bearings generally used in main and tail rotors
are classified as ABEC Class 3, 5, or 7. Class 7 is the highest quality presently
available. Satisfactory completion of the endurance tests of §§ 27.923 and 27.927 is a
means of proving that use of a particular bearing is satisfactory.




                                                          Page C - 19

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →