FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-18

PDF page 168 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 168
AC 27-1B · C-18Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

         (1) Primary controls, pilot and copilot, should be designed for the limit pilot
forces specified in paragraph (a) of the rule unless higher forces are used.

         (2) For other operating controls, such as flap, tab, stabilizer, rotor brake, and
landing gear, design limit forces are specified in paragraph (b).

     b. Procedures.

         (1) Design loads specified in the rule may be used in required structural tests
and in any structural strength analysis of the control systems submitted in compliance
with other rules.

         (2) Operation tests of the control systems noted in other rules require
application of these forces also.

AC 27.399.  § 27.399 DUAL CONTROL SYSTEM.

     a. Explanation. Design limit loads are specified for dual control systems. Pilot
effort forces applied in opposition and in the same direction are required for dual control
systems.

     b. Procedures.

         (1) Design loads specified in the rule may be used in required structural tests
and in any structural strength analysis submitted for compliance with the other rules.

         (2) Operation tests of the control systems, noted in other rules, require
application of these forces also.

AC 27.401.  § 27.401 (Amendment 27-3) AUXILIARY ROTOR ASSEMBLIES.

     a. Explanation.

         (1) For rotorcraft equipped with auxiliary rotors, normally called tail rotors, an
endurance test is required by § 27.923, and structural strength substantiation is
required. Section 27.401(b) specifically refers to structural strength substantiation of
detachable blade systems for centrifugal loads resulting from maximum design rotor
RPM.

         (2) The rotor blade structure must have sufficient strength to withstand not only
aerodynamic loads generated on the blade surface, but also inertial loads arising from
centrifugal, coriolis, gyroscopic, and vibratory effects produced by this blade movement.
Sufficient stiffness and rigidity must be designed into the blades to prevent excessive
deformation and to ensure that the blades will maintain the desired aerodynamic
characteristics. As a design objective, the structural strength requirements should be
met with the minimum material. Excess blade weight imposes extra centrifugal loads


Page C - 18

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →