Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
(iii) The limit design loads may not be less than 0.60 of the limit pilot
forces specified.
(iv) For example, if a small control surface or servo tab is lightly loaded, its
control system must be stiff enough to react the control surface loads and to provide
surface deflection to control the rotorcraft. The normal operational loads may be very
low, such as 10 pounds maximum. Nonetheless, the design limit load shall be
0.60 times the limit single pilot forces specified in § 27.397. Note that the system must
not yield under these loads.
(v) For example, if a dual but primary manual control system such as a
tail rotor control is lightly loaded, the control system, from the stops to the rotor blades,
may be designed for minimum loads equal to 0.60 times the limit dual pilot forces
specified in § 27.399.
(vi) If a power actuator is a part of a rotor control system, the design limit
force for the affected parts shall be the maximum output force of the actuator at any
operational condition (including any load/pressure after a single failure in the hydraulic
system).
(4) Controls proof and operation test is required by §§ 27.307(b)(2) and (b)(3),
27.681, and 27.683. This test is conducted using the design limit loads approved under
§ 27.395. (See paragraphs AC 27.681 and AC 27.683.)
AC 27.395A. § 27.395 (Amendment 27-26) CONTROL SYSTEM.
a. Explanation. Amendment 27-26 extensively rewrites § 27.395(b) to more
clearly incorporate design condition loads for typical powered control systems. New
requirements include substantiation for loads resulting from “each normally energized
power device, including any single power boost or power activator failure in the control
system.” There are also new minimum loads for control system designs in which
operational loads may be exceeded through jamming, ground gusts, control inertia, or
friction. The old loads were 0.60 times the limit pilot forces of § 27.397; the new loads
are 100 percent of the limit pilot forces specified in § 27.397.
b. Procedures. The procedures of paragraph AC 27.395 continue to apply except
that the increased loads in § 27.395(b)(4) of 100 percent of limit pilot forces are
specified for systems where operational loads may be exceeded by jamming, ground
gusts, control inertia, or friction.
AC 27.397. § 27.397 (Amendment 27-11) LIMIT PILOT FORCES AND
TORQUES.
a. Explanation. Design forces are contained in the rule.
Page C - 17
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.