FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-16

PDF page 166 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 166
AC 27-1B · C-16Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

                   (ii)     If low operational loads may be exceeded as noted in § 27.395(b)(2),
the system shall support without yielding 0.60 of the loads specified in §§ 27.397 and
27.399 for dual control systems.

         (3) Section 27.695 concerns standards for a power boost and power-operated
control system. This standard, in effect, imposes a fail-safe standard for hydraulic
aspects of a control system. Where appropriate to a particular design, the control
system must therefore sustain without yielding, the maximum output force of the
actuator when complying with § 27.395(a). The pilot input forces are not added to the
actuator output forces according to this standard for normal category rotorcraft. These
forces are independently applied to the control system.

         (4) Control system design features and tests requirements are found in
§§ 27.619 and 27.625, respectively. Special factors such as casting, bearing, and fitting
factors that may be appropriate for the design are contained in §§ 27.619 and 27.625,
respectively.

     b. Procedures.

         (1) The design criteria and/or a design loads report that includes the primary
control system design loads should be submitted for FAA/AUTHORITY approval.

         (2) The rotorcraft control system may be tested to ultimate design loads or may
be analyzed for the ultimate design loads. See paragraph AC 27.307.

                  (i)   A static test proposal for testing the control system to show
compliance with the rules should be approved before conducting the test. Where
compliance is to be determined by tests, limit load tests, as discussed in
paragraph AC 27.681, and/or ultimate load tests may be performed. Test results shall
be documented.

                   (ii)     If tests are not conducted, a structural analysis of the control system is
required. Appropriate factors from §§ 27.623 and 27.625 must be used as specified.
Tests may not be required when adequate similarity of systems and support structure is
determined and where adequate structural analysis is furnished.

         (3) If a part of the control system is not stiff or rigid enough to react the design
loads specified in §§ 27.397 and 27.399, that part of the system may be substantiated
for lower loads as prescribed.

                  (i)   The limit design loads are those loads specified in §§ 27.397 and
27.399;

                   (ii)   The maximum that can be obtained in normal operation and that is
allowed by the system; except



Page C - 16

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →