FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-15

PDF page 165 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 165
AC 27-1B · C-15Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

             SUBPART C - STRENGTH REQUIREMENTS

             CONTROL SURFACE AND SYSTEM LOADS


AC 27.391. § 27.391 CONTROL SURFACE AND SYSTEM LOADS--GENERAL.

     a. Explanation. This general standard concerns requirements for design loads of
tail rotors, control or stabilizing surfaces, and their control system.

     b. Procedures. The design criteria and/or the design loads report shall contain
the loads dictated by the referenced rules. (See paragraphs AC 27.395, AC 27.397,
AC 27.399, AC 27.401, AC 27.403, AC 27.411, and AC 27.413.)

AC 27.391A.    § 27.391 (Amendment 27-26) GENERAL.

     a. Explanation. Amendment 27-26 adds an explicit reference to § 27.427,
Unsymmetrical Loads (paragraph AC 27.427), to clarify that substantiation for
unsymmetrical loads is a general control surface requirement. A reference to § 27.399,
Dual Control System (paragraph AC 27.399), is also added for clarification. In addition,
§§ 27.401, 27.403, and 27.413 were removed by this amendment since these
references and requirements were adequately addressed in other standards.

     b. Procedures. The referenced AC paragraphs become paragraphs AC 27.395,
AC 27.397, AC 27.399, AC 27.411, and AC 27.427.

AC 27.395.  § 27.395 CONTROL SYSTEM.

     a. Explanation. Control system design loads and the application of these loads
are contained in this rule.

         (1) Paragraph (a) of the rule specifies the way or means of reacting the
minimum design loads specified in §§ 27.397 and 27.399 (for dual control systems).
Except reduced design loads, not less than 0.60 of those specified in §§ 27.397 and
27.399 for dual control system, may be used as specified. The standard also applies to
those control systems that may have more than one stop in a system. The design loads
must be imposed on the system from the pilot’s control to any stop in the control
system.

         (2) Minimum design loads imposed on the control system from a stop to a rotor
blade or a control surface or device shall be:

                  (i)   The maximum pilot forces obtainable in normal operation; and





                                                          Page C - 15

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →