FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-14

PDF page 164 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 164
AC 27-1B · C-14Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

AC 27.361  § 27.361 (Amendment 27-23) ENGINE TORQUE.

     a. Explanation.

         (1) The rotorcraft shall be designed for limit engine torque values, as prescribed
by the rule, to account for maximum engine torque, including certain transients and
torsional oscillations. Amendment 27-23 separated the standard into paragraphs for
turbine and reciprocating engine limit torque values.

         (2) Turbine engine limit torque for design purposes (Amendment 27-23) was
redefined into four cases and the torque values determined will be used. For example,
sudden engine stoppage is introduced as one of the cases which is applied to the
engine and the engine suspension and restraint system. Emergency operation of
governor-controlled turboshaft engines is another case.

         (3) Torque factors are also specified for reciprocating engines having two or
more cylinders in paragraph (b) of the standard.

         (4) Sections 27.547(e)(1)(ii) and 27.549(d), respectively, refer to the application
of engine torque to design of main rotor structure and engine mount and adjacent
structure.

     b. Procedures.

         (1) The engine torque associated with the maximum continuous (MC) power
condition for reciprocating engines should be multiplied by the appropriate torque factor
to obtain the limit engine torque value used for structural substantiation of the rotorcraft.

         (2) The torque values associated with MC power at the minimum power-on
RPM limit should be used. Maximum power-on speed limit will result in a lower torque
value when calculating torque from design horsepower values. However, due to piston
engine power output characteristics, an engine may produce a higher torque at higher
engine speeds contrary to the previous statement. The torque factor should account for
this characteristic.

         (3) Turbine engine limit torque values are determined for the four cases
specified. Two cases are related to the endurance test of §§ 27.923 and 27.927.

         (4) For sudden stoppage of turbine engines the engine manufacturers can
reasonably provide FAA/AUTHORITY approved data to the applicant on inertia of
rotating parts and the deceleration time expected in the event of sudden engine
stoppage. This condition usually generates critical loads in the engine mounting and
restraint system. These manufacturer’s data should be acceptable for use in
compliance with this part of the standard.




Page C - 14

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →