FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-10

PDF page 160 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 160
AC 27-1B · C-10Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 2                                                           4/25/06

         (1) Suddenly. For the purpose of this section, ‘suddenly’ is defined as an
interval not to exceed 0.2 seconds for complete control input. A rational analysis may
be used to substantiate an alternative value.

         (2) Zero Yaw. Normal, 1-g, level flight condition with either zero bank angle or
zero sideslip.

     b. Explanation. The rule requires a rotorcraft “structural” yaw or sideslip design
envelope. This sideslip envelope must cover minimum forward speed, or hover, to VH
or VNE, whichever is less. The rotorcraft must be structurally safe for the thrust
capability of the directional control system.

          (1) The rotorcraft structure must be designed to withstand the loads for
the specified yawing conditions. The standard does not require a structural flight
demonstration.  It is a structural design standard.

         (2) This standard applies only to power-on conditions. Autorotations need not
be considered.

         (3) This standard requires the maximum allowable rotor RPM consistent with
the flight conditions, including special operational rotor settings.

         (4) For the purposes of this section, the analysis may be performed at
international standard atmosphere (ISA) sea level conditions.

          (5) The rotorcraft structure must be designed to withstand the loads for
the specified sideslip conditions. This includes, but is not limited to:

                  (i)   Main cabin, tailboom, and vertical control surfaces.

                   (ii)    Tail rotor structures, including the fitting attachments to the frame.

                    (iii)  Windows, doors, and other transparencies.

               (iv)  Landing gear and retracting mechanism.

              (v)   Fairings and cowlings.

         (6)  Maximum displacement of the directional control, except as limited
by pilot effort (§ 27.397(a)), is required for the conditions cited in the rule.
Control system limiting devices may be used, however the probability of failure or
malfunction of these system(s) should be considered (see Figure AC 27.351-2).
This evaluation may include Flight Manual Limitations, if failure of the system is
reliably indicated to the crew.

         (7) Both right and left yaw conditions should be evaluated.


Page C - 10

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →