Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
4/25/06 AC 27-1B, Chg 2
(2) Gust loads for any horizontal stabilizing surface should be derived for
vertical gusts, upward and downward.
b. Procedures.
(1) Either sharp-edged (instantaneous) gusts or sharp-edged gusts modified by
an alleviation (attenuation) factor may be used for calculating aerodynamic loads for the
rotorcraft and any installed stabilizing surfaces. The following conditions may be used:
(i) Vertical gusts may be considered normal to the flight path of the
rotorcraft except during hover or low speed flight (20 knots or less) when the gusts may
be assumed normal to the longitudinal axis of the rotorcraft.
(ii) A primary effect of encountering the gust is to change the lift of the
rotors and rotorcraft surfaces. Of primary concern is the gust load or lift created by the
main rotor or rotors. The lift increment of the horizontal stabilizing surface and fuselage
is generally negligible when compared to the rotor and may be neglected for the
rotorcraft gust load determination if proven negligible by analysis.
(iii) The rotorcraft shall be assumed in stabilized level flight prior to
meeting the gust.
(iv) The gust velocity may be assumed uniform across the rotorcraft.
(v) Gust loads on the stabilizing surfaces are required as stated in
paragraph AC 27.413.
(2) The rotorcraft design maneuvering load factors may generally exceed the
design gust load factors calculated in compliance with this rule. This may be attributed
to the small incremental change in lift due to the 30 FPS gust. Nonetheless, design
gust loads for the rotorcraft shall be calculated as specified in the rule to ensure the
rotorcraft maneuvering load factors do, in each case, exceed the design gust load
factor.
(3) For further information about rotorcraft gust response characteristics, see
Paper No. 9 presented at the AHS/NASA -Ames Specialist’s Meeting on Rotorcraft
Dynamics, February 13-15, 1974. The paper, entitled, “Helicopter Gust Response
Characteristics Including Unsteady Aerodynamics Stall Effects,” was written by P.J.
Arcidiacono, R.R. Berquist, and W.T. Alexander, Jr. References listed in the paper may
be helpful also.
AC 27.351. § 27.351 (Amendment 27-26) YAWING CONDITIONS.
a. Definitions.
Page C - 9
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.