FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-8

PDF page 158 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 158
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

AC 27.339  § 27.339 (Amendment 27-11) RESULTANT LIMIT MANEUVERING
          LOADS.

     a. Explanation. The rule specifies or defines the application of rotor and lift
surface loads to the rotorcraft.

         (1) The design maneuvering load factors required by § 27.337 will result in or
be derived from rotor thrust or lift and from auxiliary surface lift.

         (2) Sections 27.321, 27.337, and 27.341 all complement one another and result
in the derivation of design flight loads that will be imposed to ensure structural integrity
of the rotorcraft.

         (3) The following assumptions and conditions are specified in the rule.

                  (i)   The rule requires application of appropriate loads at each rotor hub
and auxiliary lifting surface.

                   (ii)   Power-on and power-off flight with maximum design rotor tip speed
ratio and specific conditions that must be considered.

                    (iii)   Rotor tip speed ratio, defined in the rule, has been carried forward
from the initial rotorcraft certification rules issued in 1946. The rotor tip speed ratio is a
basic parameter used in calculating rotor aerodynamic forces.

     b. Procedures.

         (1) The rule specifies an acceptable assumption concerning application of the
rotorcraft maneuvering loads.

         (2) The rotor tip speed ratio is a parameter found in textbooks and other books
such as NACA Report No. 716. The equation in the rule contains angle “a.” Report
No. 716 also defines angle “a” as the angle of attack of the rotor disk. This definition is
more easily understood than the definition contained in the rule.

         (3) The rotorcraft design loads are derived as prescribed by §§ 27.321, 27.337,
and 27.341. These loads are applied to the rotor or rotors and any auxiliary surface as
prescribed by this rule.

AC 27.341  § 27.341 GUST LOADS.

     a. Explanation.

         (1) The rotorcraft must be substantiated for the loads derived from 30 feet per
second vertical gusts from hovering to 1.11 VNE (i.e., VD).



Page C - 8

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →