FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page C-11

PDF page 161 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 161
AC 27-1B · C-11Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

4/25/06                                        AC 27-1B, Chg 2


         (8) For vertical stabilizers, the airloads may be assumed independent of the tail
rotor thrust (superpositioning).

         (9) Loads associated with sideslip angles exceeding the values of Figure
AC 27.351-1 do not need to be considered. The corresponding points of the maneuver
may be deleted.

      c. Procedure. The design loads should be evaluated within the limits of
Figure AC 27.351-1 or the maximum capability of the rotorcraft, whichever is less; at
speeds from zero to VH or VNE, whichever is less, for the following phases of the
maneuver:

         (1) With the rotorcraft at an initial trim condition (1 g level flight and zero yaw),
the cockpit directional control is suddenly displaced to the maximum deflection limited
by the control stops or by the maximum pilot force specified in § 27.397(a). This is
intended to generate a high tail rotor thrust.

         (2) While maintaining maximum cockpit directional control deflection, within the
limitation specified in c(1) of this AC paragraph, allow the rotorcraft to yaw to the
maximum transient sideslip angle or to the value defined in Figure AC 27.351-1,
whichever is less. This is intended to generate high aerodynamic loads.

         (3) Allow the rotorcraft to stabilize at the maximum steady-state sideslip angle.
In the event that the maximum steady state angle is greater than the value defined in
Figure AC 27.351-1, the rotorcraft should be trimmed to the value of the angle using
less than maximum cockpit directional control deflection.

         (4) With the rotorcraft yawed to the static equilibrium sideslip angle specified in
c(3) of this AC paragraph, the cockpit control is suddenly returned to its initial trim
position. This is intended to combine a high tail rotor thrust and high aerodynamic
restoring forces.





                                                          Page C - 11

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →