FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-66

PDF page 145 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 145
AC 27-1B · B-66Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99

natural frequencies approximately 0.7 times the main rotor RPM. Therefore, for
example, for a rotorcraft with an in-plane frequency of 0.3/rev, operating at 300 RPM,
and with 6 inches of total lateral cyclic stick displacement, the stick should be rotated for
5 revolutions in a 0.6-inch-diameter circle at ((1-.03) x 300 RPM) or 3.5 cycles per
second to attempt excitation of possible resonant frequencies. At the conclusion of the
excitation, the cyclic stick should be returned to the neutral position while continuing the
recording of data listed in paragraph b(13).

         (8) The excitation process should include cyclic excitation inputs from the
directional and longitudinal controls if critical for the type of rotorcraft being evaluated.

         (9) If onset of ground resonance is encountered, one possible corrective action
is to increase the collective pitch and rotor speed and become airborne. However,
lowering the collective pitch and applying the rotor brake (if installed) or rolling off the
throttles has been effective for some designs and is considered a satisfactory procedure
if resonance can be consistently stopped.

        (10) With the rotor speed stabilized, landing should be made at a touchdown
speed which minimizes risk.

        (11) Special Considerations.

                  (i)   The influence of variables, including environmental effects,
corresponding aircraft component characteristic changes, operational parameters, and
surface conditions should be investigated over the ranges proposed for certification.
Additionally, the potential of misservicing and possible failure modes should be
evaluated. For ground resonance qualification, where practical, variations from the
baseline test configuration may be accomplished by ground run (§ 27.663(b) requires
investigation of probable ranges of damping), analyses, component tests, aircraft shake
test, the specification of special operational procedures in the rotorcraft flight manual, or
a combination thereof. Detailed and rational analyses showing acceptable correlation to
the baseline tests, and for which the input parameters were verified by drawings,
calculations, component static or dynamic tests, or by aircraft shake tests simulating the
conditions/configurations in question, may be used to limit testing to only those
variables and operational conditions showing marginal or unacceptable system
damping.  All operational limitations should be clearly stated in the rotorcraft flight
manual. A report of the analytical results and/or test results should be submitted per
§ 27.663.

                   (ii)   Potential instability while airborne, called “air resonance,” may occur
due to the dynamic coupling of the rotor flexibility and the pylon restraint flexibility. The
same considerations apply to air resonance as to ground resonance except that the
pylon restraint variables replace the landing gear variables. Air resonance should be
addressed in the certification program.




Page B - 66

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →