FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-65

PDF page 144 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 144
AC 27-1B · B-65Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/30/99                                             AC 27-1B

         (1) Under all conditions, any oscillations which may be introduced should be
damped. However, no instability should occur at any operating condition such as during
RPM changes from minimum to maximum and idle to maximum. For rotorcraft with
wheel gear, uneven taxi surfaces in conjunction with particular taxi speeds, may excite
ground resonance and should be evaluated by taxiing on typical surfaces. This
evaluation may be conducted in conjunction with the tests of § 27.235. In operation, the
resonance characteristics should be checked during takeoff and landing at zero speed
and during run-on landings using various power values.

         (2) For those aircraft equipped with Stability Augmentation Systems (SAS), all
ground resonance investigations should be conducted with SAS on and SAS off. This
includes the hovering and running takeoffs and landings, taxi tests, and specific ground
resonance tests noted herein. Consideration should be given to conducting tests in
various SAS configurations such as roll channel on and pitch channel off, where such
configurations are possible and authorized.

         (3) For each rotorcraft configuration tested, the aircraft should be positioned on
the ground in flat pitch with the rotor stabilized at the minimum practical rotational speed
or optionally at a speed shown analytically to have significant margin from indicated
resonant conditions. Control system inputs should be used to disturb the system for
evaluation of subsequent damping.

         (4) For each incremental increase in rotor speed and for each rotor speed
setting at increments of collective pitch settings, cyclic and collective inputs should be
investigated prior to proceeding to the next rotor speed setting. These inputs should
cover the appropriate range and combinations of amplitude and frequency. The
collective pitch setting increments should range from flat pitch to light on the landing
gear prior to fully airborne, depending upon the test sequence for minimum risk.

         (5) Cyclic pitch inputs should be made either by the pilot through the cyclic stick
or through a signal-generating device working in conjunction with the cyclic controls.
For each frequency of input, amplitude of the inputs should be increased incrementally
and ultimately should be large enough to generate responses representative of normal
ground and flight operation on the rotor and support system. The inputs should
continue for a time sufficient to obtain representative responses, typically time sufficient
to execute five complete circles of the cyclic stick (about neutral) at the selected
frequency.

         (6) The excitation frequency should be such as to excite the blade in-plane
frequency. Rotor speed settings should be increased to 1.05 times the maximum
power-on rotor speed. Collective pitch settings should be increased in increments of
not more than 20 percent to maximum collective or alternately to the collective setting
required to become partially airborne (when the cyclic is displaced as noted).

         (7) Typically, articulated rotor aircraft have natural frequencies on the blade in
lag of approximately 0.3 times the power-on main rotor RPM. Soft in-plane rotors have


                                                       Page B - 65

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →