FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page B-62

PDF page 141 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 141
AC 27-1B · B-62Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


     b. Procedures. The structural substantiation data contain the allowable design
limits for the rotorcraft. A calibrated accelerometer or load factor “g” meter should be
installed as near as practicable to the rotorcraft CG to record the maximum vertical load
factor attained. Instrumentation of the landing gear and/or related structure may also be
an acceptable means of showing compliance.

         (1) Calibrated instrumentation should be installed to record the maximum loads
or maximum vertical load factor attained during the taxi tests.

         (2) The taxi surface should be evaluated for compliance with the rule.
Corrugated surfaces as well as broken or uneven surfaces (in accordance with the rule)
should be used.

         (3) Representative typical taxi speeds, up to the maximum selected by the
applicant, should be attained over the selected taxi surfaces.

         (4) A light and heavy rotorcraft weight condition should be evaluated.

         (5) Limitations appropriate for the rotorcraft design should be included in the
flight manual.  If these tests indicate that it is unlikely that limit load factors will be
attained while taxiing, flight manual limitations may not be necessary.

         (6) Pertinent taxi information obtained from these test conditions may be
included in normal procedures of the flight manual.

AC 27.239.  § 27.239 SPRAY CHARACTERISTICS.

     a. Explanation. The intent of this requirement is to evaluate by demonstration that
water spray does not obscure visibility (day or night) or damage the rotorcraft during
normal waterborne operation (for those rotorcraft which have waterborne or amphibious
capability).

     b. Procedures.

         (1) The following maneuvers should be evaluated in ambient conditions up to
the proposed sea state or wave height for operation.





Page B - 62

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →