Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/30/99 AC 27-1B
SUBPART B - FLIGHT
GROUND AND WATER HANDLING CHARACTERISTICS
AC 27.231. § 27.231 GROUND AND WATER HANDLING CHARACTERISTICS-
GENERAL.
a. Explanation. The rule states: “The rotorcraft must have satisfactory ground
and water handling characteristics, including freedom from uncontrollable tendencies in
any condition expected in operation.” In addition, §§ 27.235, 27.239, and 27.241
contain specific requirements concerning ground and water handling characteristic
evaluations.
b. Procedures.
(1) During the flight test program and the F&R program (§ 21.35(b)(2)), the
rotorcraft will be subjected to evaluations at various weight and CG conditions. Any
uncontrollable tendencies found during these test programs must be corrected.
(2) Controllable or damped vibrations or oscillations on the ground or in the
water are acceptable, provided the design limits of the rotorcraft are not exceeded.
(3) Any significant vibration or oscillation characteristics found during tests
should be described in the test report, and the rotorcraft flight manual should contain
appropriate descriptions and procedures to describe and either avoid or handle
significant characteristics.
(4) For rotorcraft equipped with wheel gear, the evaluation should include
takeoff, landing, and taxi at the maximum speed and at CG extremes. If a nose or tail
wheel lock/swivel control is installed, each position should be evaluated for limiting
takeoff, landing, and taxi speeds. Maximum substantiated speed values should be
included in the RFM as limitations.
(5) For water operations, the wave height and frequency or “sea state” should
be included as a limitation or, if no limit was reached during testing, the demonstrated
values should be placed in the Performance Section of the RFM. Information or limits
on the allowable “sea state” for rotor startup and shutdown should also be included.
AC 27.235. § 27.235 TAXIING CONDITION.
a. Explanation. The rotorcraft is designed for certain landing load factors
(§§ 27.471 and 27.473). The rotorcraft must not attain a load factor in excess of the
design load factor when taxied over the roughest ground that may reasonably be
expected in normal operation at the expected taxi speeds. This rule applies to wheel
landing gear equipped rotorcraft.
Page B - 61
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.