Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
9/17/2009 AC 27.1B, Chg4
b. Procedures.
(1) The control requirement of this section is so essential to basic flight
mechanics that compliance may be found during conventional flight testing for
compliance with other portions of the regulations. No special or designated testing
should be required.
(2) The procedures necessary to ensure compliance with the stability
requirements of this section are contained under § 27.175.
AC 27.173A. § 27.173 (Amendment 27-44) STATIC LONGITUDINAL STABILITY.
a. Explanation.
(1) Amendment 27-44 makes a major change to the requirement by allowing for
neutral or negative static longitudinal stability in limited flight domains. Additionally the
requirement for the hover demonstration found in § 27.173(c) has been deleted as this
requirement is adequately covered by the controllability requirements. The basic
tenants of the rule are unchanged in that the rule contains control system design
requirements for both stability and control. Paragraph (a) contains the basic control
philosophy necessary for all civil aircraft. Forward motion of the cyclic control must
produce increasing speeds and aft motion must result in decreasing speeds. For
rotorcraft, this is accomplished with throttle and collective held constant. This
requirement in no way assures aircraft stability. It is simply a control requirement that
speaks to direction of control motion. Rotorcraft with either highly stable or highly
unstable static longitudinal stability characteristics can typically comply with the basic
requirement for control sense of motion. All the policy material pertaining to this section
remains in effect with the following changes and additions:
(2) §§ 27.173 through 27.175 contain the basic control position requirements
necessary to establish a minimum level of static longitudinal stability. Positive stability is
found for conditions of climb, cruise, VNE, and autorotation in § 27.175 by demonstrating
a stable stick position gradient through a specified speed range. This is the primary
method of demonstrating compliance with the longitudinal static stability requirements.
(3) For aircraft that do not possess positive control position stability for some
limited flight conditions or modes of operation, an equivalent level of safety was
previously provided which requires a qualitative evaluation of the pilot’s ability to
maintain a given airspeed, within 5 knots of the desired speed, without exceptional
piloting skill or alertness. These flight conditions and modes of operation could include
various combinations of gross weight, CG, flight regime (climb, cruise, descent),
ambient conditions (altitude/temperature) as well as possible variations in the stability
augmentation configuration. In the past, the FAA/AUTHORITIES have certified
numerous rotorcraft, under equivalent level of safety findings, which have neutral or
negative static longitudinal stick position stability in some flight domains. This
amendment to § 27.173 is intended to allow for this case without having to resort to an
Page B – 55
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.