Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27.1B, Chg4 9/17/2009
equivalent safety finding. For these previous equivalent safety findings, acceptable
qualitative flight characteristics were found on aircraft, which possessed negative
longitudinal stick position gradients of up to 2-3% of total control travel in certain flight
regimes; however, this value is not intended to be a limit. When this means of
compliance is elected by the applicant, in addition to the qualitative pilot evaluation, it is
still necessary to collect the data associated with the classical static longitudinal stability
testing as defined in § 27.175.
b. Procedures. All the policy material pertaining to this section remains in effect
with the following changes and additions:
(1) The control requirement of paragraph (a) of this section is so essential to
basic flight mechanics that compliance may be found during conventional flight-testing
for compliance with other portions of the regulations. No special or designated testing
should be required.
(2) The procedures necessary to assure compliance with the primary stability
requirements of this section are contained under § 27.175, Demonstration of Static
Longitudinal Stability. Refer to AC 27.175 of this advisory circular for an explanation of
detailed flight test procedures.
(3) The procedures necessary to assure compliance with the alternative (i.e.,
pilot evaluation) method of compliance are provided below.
(i) For those limited conditions where compliance with the basic control
position requirements cannot be shown, the evaluation must focus on the ability of the
pilot to maintain airspeed in the flight regime without exceptional piloting skill or
alertness under typical flight conditions. “Limited flight conditions” infers that the aircraft
should be in reasonable compliance with the stick position stability requirements of
§ 27.173(b) for most of the flight conditions and configurations tested. Extraordinary
means of complying with § 27.173(b) should not be forced on the aircraft design if the
airspeed retention task meets the pilot skill and alertness guidelines. The
demonstration flight regimes are defined in § 27.175(a) through (d). For those flight
regimes, conditions and configurations where compliance with stick position
requirements of § 27.173(b) cannot be shown, the evaluation pilot should assess the
ease of maintaining airspeed within the specified +/- 5 knots.
(ii) When assessing the ease of maintaining airspeed the total workload must
be considered. Secondary tasks pertinent to the minimum flight crew in each flight
regime should be conducted. This may include visual navigation and communication in
cruise, traffic avoidance in climb, and landing site selection in autorotation.
(iii) The cues that the aircraft provides are an important contributor to the
evaluation, and the nature of these cues should be noted in the compliance report
where this alternate qualitative evaluation determines that the aircraft has satisfactory
Page B – 56
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.