Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B 9/30/99
b. Procedures.
(1) Compliance with the requirements of this section can often be obtained for
the VFR condition without any specific or designated flight testing. If the rotorcraft is
marginal in regard to pilot strain and fatigue, the FAA/AUTHORITY pilot should be
assured, through special tests if necessary, that the aircraft can be satisfactorily flown
throughout the maximum endurance capabilities of the rotorcraft including night and
turbulence conditions if those are critical. This test should be conducted with minimum
required systems in the aircraft and with minimum flightcrew.
(2) Reasonable failure conditions which add to pilot workload, strain, and
fatigue should be evaluated (electrical, hydraulic, and mechanical failures, etc.). The
necessary times associated with flight with a failed system must be appropriate to the
flight manual procedures for each failure. A failure condition requiring immediate
landing would obviously require shorter evaluation time than a condition allowing
continued flight to destination.
(3) IFR approvals necessitate a careful evaluation of paragraphs b (1) and (2)
above. In IFR operations, weather conditions frequently necessitate continued flight to
destination or diversion to alternate airports with critical failures. Immediate landing
may not be feasible. The evaluating pilot must ensure pilot strain and fatigue are
acceptable during typical flight profiles for each type of operation to be approved.
AC 27.173. § 27.173 (Amendment 27-21) STATIC LONGITUDINAL STABILITY.
[See new AC 27.173A (dated 9/17/2009) posted as separate document in RGL with this Master AC.]
a. Explanation.
(1) This rule contains control requirements for both stability and control.
Paragraph (a) contains the basic control philosophy necessary for all civil aircraft.
Forward motion of the cyclic control must produce increasing speeds, and aft motion
must result in decreasing speeds. For rotorcraft, this is accomplished with throttle and
collective held constant. Rotorcraft with either highly stable or highly unstable static
longitudinal stability characteristics can typically comply with the basic requirement for
control sense of motion. However, the intent and interpretation of this paragraph is to
provide a stable stick position versus airspeed gradient. Therefore, a stabilized
airspeed less than the trim speed requires a cyclic stick position aft of the trim stick
position, and a stabilized airspeed greater than the trim speed requires a cyclic stick
position forward of the trim speed stick position.
(2) The remainder of § 27.173, through reference to § 27.175, contains the
basic control position requirements necessary to establish a minimum level of static
longitudinal stability. Positive stability is found for conditions of climb, cruise, and
autorotation in § 27.175 by requiring a stable stick position gradient through a specified
speed range. A defined level of instability is permitted for the hovering condition.
Page B - 54
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.