FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 120

PDF page 120 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 120
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

9/17/2009                                      AC 27-1B, Chg 4


The flight control system should be evaluated to determine whether an actuator jammed
in an extreme position would result in reduced control margins. Generally, if the flight
control system stops are between the actuator and the cockpit control, the control
margin will be affected.  If the control stops are between the actuator and the rotor
head, the control margins may not be affected, but the location of the cockpit control
may be shifted. This could produce interference with other items in the cockpit. An
example of this would be a lateral actuator jammed hardover causing a leftward shift in
the cyclic stick position. Interference between the cyclic stick, the pilot's leg, and the
collective pitch control could reduce the left lateral control available and reduce left
sideward flight capability. In the case of fly-by-wire surfaces, both the high-speed
forward flight controllability and the rearward flight capabilities could be affected. Flight
control systems that incorporate automatic devices should be thoroughly evaluated for
critical areas. Every failure condition that is questionable should be flight tested with the
appropriate actuator fixed in the critical failure position. These failures may require
limitations of the flight envelope. Any procedure or limitation that must be observed to
compensate for an actuator hardover or softover malfunction should be included in the
RFM.

     b. Procedures. The policy material pertaining to this section remains in effect with
the following changes and additions:

         (1) Flight test instrumentation should include ambient parameters, all flight
control positions, rotor RPM, main and tail rotor flapping (if appropriate), engine power
instruments, and throttle position. Flight controls that are projected to be near their
limits of authority should be rigged to the most adverse production tolerance. A very
accurate weight and balance computation is needed along with a precise knowledge of
the aircraft's weight/CG variation as fuel is burned.

         (2) The critical condition for VNE controllability testing is ordinarily aft CG, MC
power, and minimum power-on rotor RPM, although power and RPM variations should
be specifically evaluated to verify their effects. The turbine engine is sensitive to
ambient temperatures, which affect the engine's ability to produce rated maximum
continuous torque. Flight tests conducted at ambient temperatures that cause the
turbine temperature to limit MCP would not produce the same results obtained at the
same density altitude at colder ambient temperatures where maximum continuous
torque would be limiting. Forward CG should be spot checked for any "tuck under"
tendency at high speed. The VNE controllability test is normally accomplished shortly
after the 1.1 VNE (or 1.1VH ) point obtained during stability tests required by § 27.175(b).
Controllability must be satisfactory for both conditions. If VNE varies with altitude or
temperature, VNE for existing ambient conditions is utilized for the test. Extremes of the
altitude/temperature envelope should be analyzed and investigated by flight test.

         (3) Controllability.

                  (i) The critical condition for controllability testing in a hover is ordinarily
forward CG at maximum weight with minimum power-on rotor RPM. For rearward flight


                                                     Page B – 52.5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →