Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 9/17/2009
testing of configurations where the forward CG limit varies with weight, low or high gross
weight may be critical. Lateral CG limits should also be investigated. A calibrated pace
vehicle is needed to assure stabilized flight conditions. Surface winds should be less
than 3 knots throughout the test sequence. Testing can be done in higher stabilized
wind conditions (gusting less than 3 knots); however, these conditions are very difficult
to find and the method is very time consuming due to the necessity of waiting for
stabilized winds. Testing in calm winds is preferred. IGE hover controllability testing
should be accomplished with the lowest portion of the helicopter at the published hover
height above ground level; however, the test altitude above the ground may be
increased to provide reasonable ground clearance. OGE testing should be done with
the rotor at a predetermined height above the ground at which it has been determined
that there is no ground effect. Although the necessary yaw response will vary
somewhat from model to model, sufficient control power should be available to permit a
clearly recognizable yaw response after full directional control displacement when the
helicopter is held in the most critical position relative to wind.
(A) Testing will normally be carried out at the power required to achieve
stabilized flight conditions. However, it is also important to show that yaw control
remains adequate to allow normal power changes that might be required in normal
operational maneuvers typical for the type and use of the rotorcraft. With rotorcraft that
are operating in conditions in which the gross weight is limited by the power available,
there should always be adequate tail rotor pedal control available to maintain yaw
control when using up to take-off power. However, this will not be the case if the
rotorcraft weight in the low speed flight envelope is limited by yaw control system
capability.
(B) To cover the case where excess power is available, it is appropriate to
examine the rotorcraft characteristics with some small amounts of additional power
applied above the trim power required to hover to allow for typical power variations that
will be experienced during normal use of the rotorcraft. For example, maneuvering or
turbulence will cause the pilot to use some of the excess power available. The
rotorcraft should be flown, both IGE and OGE, with the most adverse wind speed and
direction for directional control within the flight envelope proposed. Use power
variations above trim that might be expected during normal use of the rotorcraft giving
consideration to the amount of excess power available, the ease with which power can
be controlled by collective, and the characteristics of the rotorcraft if the limits of
directional control are approached. There should be no tendency to deviate rapidly or
suddenly in yaw. This assessment is normally conducted in conjunction with the critical
azimuth testing.
(C) It may be appropriate to provide flight manual information on the
directional control characteristics, including any relevant maximum power above which it
could be expected that directional control might not be maintained.
Page 52.6
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.