FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx B-6

PDF page 1180 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1180
AC 27-1B · Apdx B-6Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                                       2/4/2016


                (A) AFCS Malfunction Assessment. Failure conditions in the AFCS, including SAS, ATT,
FD and AP functions, that are not shown to be extremely improbable must be demonstrated in flight.
Assessment of failure conditions has the following elements:

                      (1) Failure condition insertion.

                      (2) Pilot recognition of the effects of the failure condition.

                      (3) Pilot reaction time (that is, the time between pilot recognition of the failure
condition and initiation of the recovery).

                      (4) Pilot recovery.

                (B) Failure Condition.

                      (1) Failure Conditions. The AFCS failure conditions should be simulated such that
overall response is representative of the actual effect of that failure condition on the aircraft and its
systems.

                      (2) Most Critical Conditions. The aircraft loading and flight conditions under which
the failure condition is inserted should be the most critical. Examples of these conditions are CG, weight,
altitude, speed, and power.  If the AFCS includes coupling to the collective axis, the tests should be
performed with the collective axis both coupled and uncoupled.

                (C) Pilot Recognition and Response Time.

                      (1) The pilot recognition and response time is dependent on pilot involvement in the
flying task, which is defined as “active,” “attentive,” and “passive” flight. The pilot’s involvement in the
flying task is dependent on the level of stabilization provided by a particular mode of the AFCS, as well as
the phase of flight.

                                     (i) Active flight - any flight segment during which the characteristics of the aircraft
necessitate continuous flying of the rotorcraft by the pilot using the primary flight controls. Active flight
includes take-off, hover, and landing.

                                       (ii) Attentive flight - any flight segment requiring attention from the pilot for short
periods. Attentive flight can be further subdivided into hands-on and hands-off. Attentive, hands-on
addresses phases of flight where the AFCS is controlling the flight path, but close attention is required
from the pilot. Examples include coupled hover and coupled approach. Attentive, hands-off addresses
flight phases where the controls can be released for extended periods of time, but where the pilot is
expected or required to continue to monitor the behavior of the aircraft and system. Examples include
using the following AFCS modes in climb, cruise, hold, and descent: a more basic attitude hold such that
the pilot is required to monitor the series actuator authority and correct as necessary; or an AP mode if an
AFCS malfunction results in a caution message and the applicable emergency or abnormal procedure
requires the pilot to be attentive.

                                         (iii) Passive flight - any flight segment of long duration requiring the minimum of
attention from the pilot. This can be further subdivided into hands-on and hands-off, the latter being
applicable if the rotorcraft automatic flight control system allows the pilot to release the flight controls for
substantial periods of time. Passive hands-on flight may include using attitude retention modes of the
AFCS in climb, cruise, hold, and descent. Passive hands-off flight may include using AP modes in climb,
cruise, hold, and descent.

Note:    It is not acceptable to use reduced pilot response times based on rotorcraft flight manual (RFM)
         limitations requiring the pilot to be hands-on if hands-on flight is not appropriate to the level of
         stabilization and flight path control provided by the AFCS operating mode.


Page Apdx B - 6

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →