FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx B-5

PDF page 1179 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1179
AC 27-1B · Apdx B-5Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

2/4/2016                                                  AC 27-1B, Chg 7


coupling occurs, these changes should be allowed to interact naturally until recovery is necessary. Due
to the sensitive nature of this test, smooth air is essential. Repeatability may be a problem. At least two
test points in each direction should be obtained at each trim condition. Results may be averaged if they
show reasonable repeatability. The same procedures may be utilized for an aperiodic pitch response;
however, a displacement of 5° from trim should be used, and of particular importance is the pitch rate
passing 10°. Again, at least two test points in each direction should be obtained for each trim condition.
Although not stated in the requirement, the flight conditions for demonstration of static longitudinal
stability are also appropriate for demonstration of dynamic stability. Rotorcraft certificated for a minimum
crew of two pilots are required to demonstrate longitudinal static force stability in the cruise and the
approach configuration. Compliance with the dynamic stability requirements should be demonstrated for
these configurations, and the rotorcraft should be free from rapid and excessive rates of divergence in the
other flight configuration. The degree of testing referred to here represents that which might be required
of a marginally stable rotorcraft. For those configurations that provide good aerodynamic stability or use
varying degrees of SAS, the scope of the demonstration program would be decreased significantly.

                    (ii) Control system dynamics should also be evaluated. This may be accomplished by lightly
bumping each control in flight and observing its free response. Any resulting control motion must dampen
quickly and should not be driven by aircraft or control system interaction. This will ensure safe flight in the
event a control is inadvertently bumped or released from an out-of-trim condition.

         (6) Automatic Flight Control System (AFCS).

                  (i) From a regulatory compliance standpoint, the AFCS used on most modern rotorcraft often
performs two different and distinct functions. These two functions are to:

                (A) Enhance the inherent basic stability of the aircraft to enable compliance with
applicable flight characteristic requirements by using automatic control features, such as SAS, which may
incorporate an attitude hold mode (ATT); and

                (B) Control aircraft flight path using a simple ATT in conjunction with the SAS or autopilot
modes (coupled flight director), such as airspeed hold, altitude hold, radio navigation, and precision
approach.

                    (ii) Definitions.

                (A) Autopilot (AP). The AP, also known as coupled flight director, is an automatic
mechanical, electrical, or hydraulic control system primarily intended to assist the flight crew in the
guidance of the aircraft. The various AP control modes are designed to provide workload relief to the
pilots and a means to fly a flight path more accurately to support specific operational requirements.

                (B) Attitude Hold Mode (ATT). ATT is an automatic flight control system mode that
maintains established pitch and roll attitudes and, in some cases, provides yaw damping, yaw hold, or
heading hold.

                (C) Flight Director (FD). The FD is a guidance system that provides an automatically
computed visual cue or set of cues, used during manual control of the aircraft as steering command
information, which direct the pilot how to maneuver the aircraft (usually in pitch, roll, and collective) to
track a desired flight path.

                (D) Stability Augmentation System (SAS). The SAS is an automatic control system mode
that augments the inherent stability of the aircraft. The SAS aspects of the AFCS are not covered in
§ 27.1329 (Automatic pilot system) but rather in § 27.672. Nevertheless, the guidance provided in this
section for pilot response times is applicable to SAS malfunction testing.

                     (iii) AFCS Malfunctions.



                                                                    Page Apdx B - 5

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →