FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

Printed page Apdx B-4

PDF page 1178 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1178
AC 27-1B · Apdx B-4Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                                       2/4/2016


addition of friction or deadband into the control system to satisfy the dihedral requirement is not
acceptable.

                  (viii) In approving small, negative dihedral values, the pilot should ensure that other positive
flight cues, such as suitable side force, accompany sideslip. This will aid the pilot in determining direction
of sideslip so that no reverse sensing or confusion accompanies sideslip conditions.

         (5) Dynamic Stability.

                  (i) Dynamic characteristics are defined in quantitative terms; however, some areas of
interpretation and technique need special consideration:

                (A) Unlike fixed-wing aircraft, where the size of the input has no effect on damping ratio,
rotorcraft can be sensitive to the type and size of input used to excite each dynamic mode. For instance,
it has been found that for the phugoid-type dynamic oscillation, damping ratio is inversely proportional to
the size of the input.  It therefore becomes important that dynamic excitations be sized to approximate the
response of the rotorcraft in a moderate, turbulent gust. In addition, the dynamic input should be made
with the control(s) that most accurately simulates the typical aircraft gust response. Obviously, for this
evaluation some flying of the rotorcraft in turbulence is necessary to obtain knowledge of the rotorcraft’s
gust response. Pulses and doublets may be used to generate disturbances similar to a gust. To assist
returning the control(s) to the trim position, a hand held jig may be used. Use of attitude and rate
instrumentation is desirable. The pilot may find that collective excitation, or collective in conjunction with
cyclic, is most appropriate for gust simulation.

                (B) The second area of concern in evaluating dynamic response is whether to let only
one axis respond to an excitation or to let the rotorcraft respond in two or more axes. When it can be
done safely, the rotorcraft should be allowed to follow its dynamic response in all axes. In other words, if
pitch oscillations feed into roll, the pilot should attempt to observe and record the total aircraft dynamic
response in both pitch and roll.

                (C) The third area concerns strict compliance with the exact wording of the dynamic
requirement. In this regard, a neutrally damped oscillation with a period of 19 seconds would not be
acceptable; however, a very divergent oscillation that doubles in amplitude in 21 seconds would be
acceptable. The 19-second oscillation is much less severe than the 21-second oscillation and yet is
unacceptable by the “letter of the law.” Figure AC 27.APX B-1 is a graphic display of the dynamic
requirement. The 19 and 21-second oscillations are shown as points (1) and (2). Point No. 1 is
positioned much more toward the acceptable portion of the graph and yet by the “letter of the law” is
unacceptable. The intent of the dynamic requirement is roughly approximated by the dashed or curved
line. Areas to the right of that line may be considered for findings of equivalent safety.

                (D) A fourth area requiring special care in testing is the aperiodic requirement. The most
common aperiodic motion is the spiral characteristic, which results when aircraft attitude is displaced in
roll. The preferred method for testing this requirement is to stabilize precisely on a trimmed condition in
straight flight, then displace the rotorcraft to 10° of bank, stabilize momentarily, set the controls as they
were positioned for straight flight, and release them. Time and bank angles are then recorded. Recovery
is initiated when bank angle or roll rate becomes excessive. Of particular interest is the time for bank
angle to pass 20°, and this time should not be so short as to cause the aircraft to have objectionable flight
characteristics in the IFR environment. The time period to double amplitude (20°) should be at least
9-seconds.  It is vitally important that controls (particularly lateral cyclic) are positioned exactly as it was
for the straight flight condition.  If a high resolution force trim system is not incorporated, an alternative
method may be used. In this second method, the rotorcraft is trimmed for straight flight as described
above and controls are released. Roll attitude may simply be allowed to vary naturally with time or small
pulse input may be made with pedals.  It is important that controls be positioned precisely as they were
for the trimmed, straight flight condition and a plot of bank angle versus time is obtained. This plot is then
compared against a divergent roll condition that doubles in amplitude every 9-seconds. Of particular
interest is again the rate passing 20° of bank.  If airspeed changes as the aircraft rolls or if roll or pitch


Page Apdx B - 4

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →