Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Extracted text for finding words
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
angle and ball widths of skid can be obtained at given speeds for use during later testing after sideslip
instrumentation is removed. A simple yaw string can be calibrated in a similar manner. The TIA should
define the maximum sideslip angles, which should not be exceeded during the flight test program. These
angles must not be greater than the structural sideslip envelope substantiated and are not required to be
that sideslip angle obtained with full directional pedal deflection. Sufficient side force cues should
accompany sideslip to alert the crew when approaching sideslip limits. This is needed to assure that
structural sideslip limits will not be inadvertently exceeded in service. Although not stated in the
requirement, flight conditions for demonstration of static longitudinal stability are also appropriate for
demonstration of static lateral-directional stability.
(ii) Dihedral requirements may be more difficult to assess. For those rotorcraft that do not
meet the position and force gradient requirements for the conventional, cross-controlled sideslips, there
are alternative tests that may be used to determine acceptable characteristics. If directional pedals are
utilized in steady sideslips, the resultant rolling tendency is the sum of (1) the aircraft’s roll due to sideslip
tendency (dihedral), and (2) the aircraft’s roll due to directional control input. If the rotorcraft has a tail
rotor that is excessively high or low in relation to the rotorcraft’s vertical center of gravity (CG), application
of tail rotor thrust will introduce a significant rolling moment. The basic intent of dihedral stability testing is
to determine the rotorcraft response to sideslip exclusive of directional control input. In general, if a tail
rotor configuration is involved and the tail rotor is above the vertical CG of the rotorcraft, the effect of
pedal input upon dihedral effect is destabilizing during conventional, control-induced sideslips.
(iii) There are two alternate methods that, for small angles of sideslip, can give an indication
of the basic dihedral stability of the rotorcraft. Both methods involve freezing the directional controls while
artificially creating sideslip by other means.
(iv) The first method is only applicable for rotorcraft with single main rotor systems. To utilize
this method, the rotorcraft is stabilized in a given flight condition and small collective (torque) changes are
applied in each direction (e.g., ±5 % and ±10 %) while holding pedals fixed. Sideslip angle, lateral control
position, and lateral control force may be measured and plotted for small torque changes from trim. This
technique will not work for aircraft that have collective to pedal or collective to lateral control couplings.
(v) In the second method, the rotorcraft is stabilized in a trimmed flight condition with a small
amount of bank (5°-10°). The rotorcraft is then rolled to an approximately equal angle of bank in the
opposite direction holding the pedals fixed. The change in direction of bank results in a small change in
sideslip angle and again sideslip angle may be plotted versus lateral control position or force. This test
should be conducted in both directions and the results averaged. This method can give reasonably
accurate results for small perturbations. Other factors contribute to the results of either of these two
methods. It is always important to assess the roll due to sideslip tendency with pedal induced sideslips to
assure lateral control forces are reasonable and in a proper direction for directional out-of-trim conditions,
and to assure the pilot has adequate sideslip cues.
(vi) Wording of the dihedral requirement is intended to allow slightly negative dihedral stability
at critical loading conditions. This will ordinarily result in positive dihedral stability throughout a great
majority of the approved loading envelope. The test for maximum allowable negative dihedral effect
would involve stabilization at a required flight condition, inducing a sideslip up to ±10° from trim, then
assessing lateral cyclic friction or deadband to determine if roll is restrained while remaining in the control
system friction or deadband so that the control may be released without resulting in the aircraft rolling in
the adverse direction. When testing for this condition, lateral cyclic friction should be adjusted to the
minimum value.
(vii) The intent of the dihedral rule is to allow small amounts of control system friction and
deadband to mask small values of negative dihedral. Where slope of the negative dihedral versus
sideslip exceeds these small values, the negative dihedral must not be approved. The operational pilot
must not be presented with opposite cyclic sensing for similar sideslip conditions as loadings and flight
conditions change. In general, large values of control system friction and deadband are undesirable. The
Page Apdx B - 3