Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 9/17/2009
AC 27.143A. § 27.143 (Amendment 27-44) Controllability and Maneuverability.
a. Explanation. Amendment 27-44 made a minor clarification to assure that in-
ground-effect (IGE) controllability is demonstrated at all speeds up to 17 knots. In many
rotorcraft, the entry into the regime of translational lift requires the most power, thus
potentially causing control difficulties, and frequently occurs at speeds less than 17
knots. The amendment also requires that, above 7,000 feet density altitude in which
takeoff and landing performance is scheduled, the controllability of the rotorcraft be
determined. The amendment also requires that out-of-ground-effect (OGE)
controllability be determined up to a speed of at least 17 knots at a weight selected by
the applicant up to the maximum takeoff and landing altitude of the rotorcraft.
All the policy material pertaining to this section remains in effect with the following
changes:
(1) This regulation contains the basic controllability requirements for normal
category rotorcraft. It also specifies a minimum maneuvering capability for required
conditions of flight. The general requirements for controllability and for maneuverability
are summarized in § 27.143(a), which is self-explanatory. The hover condition is not
specifically addressed in § 27.143(a)(2) so that the general requirement may remain
applicable to all rotorcraft types, including those without hover capability. For rotorcraft,
the hover condition clearly applies under "any maneuver appropriate to the type."
(2) Paragraphs (b) through (e) in § 27.143 include more specific flight
conditions and highlight the typical areas of concern during a flight test program.
(i) § 27.143(b) specifies flight at VNE with critical weight, center of gravity
(CG), rotor RPM, and power. Adequate cyclic authority must remain at VNE for nose
down pitching of the rotorcraft and for adequate roll control. Nose down pitching
capability is needed for control of gust response and to allow necessary flight path
changes in a nose down direction. Roll control is needed for gust response and for
normal maneuvering of the aircraft. In the past, 10 percent control travel margin has
been applied as an appropriate minimum control standard. The required amount of
control power, however, has very little to do with any fixed percentage of remaining
control travel. There are foreseeable designs for which 5 percent remaining is adequate
and others for which 20 percent may not be enough. The key is, can the remaining
longitudinal control travel at VNE generate a clearly positive nose down pitching moment,
and will the remaining lateral travel allow at least 30° banked turns at reasonable roll
rates? Moderate lateral control reversals should be included in this evaluation and
since available roll control can diminish with sideslip, reasonable out of trim conditions
(directionally) should be investigated. This "control remaining" philosophy must also be
applied for other flight conditions specified in this section.
(ii) § 27.143(c) requires a minimum control capability for hover and takeoff
in winds from zero to at least 17 knots from any azimuth. Control capability in wind from
zero to at least 17 knots must also be shown for any other appropriate maneuver
Page 52.2
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.