Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
configurations where the forward CG limit varies with weight, low or high gross weight
may be critical. Lateral CG limits should also be investigated. A calibrated pace vehicle
is needed to assure stabilized flight conditions. Surface winds should be less than
3 knots throughout the test sequence. Testing can be done in higher stabilized wind
conditions (gusting less than 3 knots); however, these conditions are very difficult to find
and the method is very time consuming due to the necessity of waiting for stabilized
winds. Testing in calm winds is preferred. Hover controllability testing should be
accomplished with the lowest portion of the rotorcraft at the published hover height
above ground level; however, the test altitude above the ground may be increased to
provide reasonable ground clearance. Although the necessary yaw response will vary
somewhat from model to model, sufficient control power should be available to permit a
clearly recognizable yaw response after full directional control displacement when the
rotorcraft is held in the most critical position relative to wind. Testing will be carried out
at the power required to achieve stabilized flight conditions. With rotorcraft that are
operating in conditions such that the gross weight is limited by the power available,
there should always be adequate tail rotor pedal authority to maintain yaw control when
using the maximum approved all engines operating (AEO) power, which is take-off
power for most designs.
(i) Where the rotorcraft is capable of operating at maximum gross weight with less
than maximum approved power, it is appropriate to examine the rotorcraft
characteristics with small amounts of additional power applied above the trim power
required to allow for typical power variations experienced during normal use of the
rotorcraft. For example, maneuvering, turbulence, or rotor governing characteristics
may cause the pilot to use power in excess of power required for trim. The maximum
power excursions should not exceed maximum approved AEO power, excluding any
transient range.
(ii) The rotorcraft should be flown both in ground effect (IGE) and out of ground
effect (OGE), with the most adverse wind speed and direction for directional control
within the flight envelope proposed, using power variations above trim that might be
expected during normal use of the rotorcraft. Consideration should be given to the
amount of excess power available, the ease with which power can be controlled via the
collective, the effect of tail rotor control inputs on power required, and the characteristics
of the rotorcraft if the limits of directional control are approached. There should be no
tendency to deviate rapidly or suddenly in yaw. This assessment is normally conducted
in conjunction with the critical azimuth testing.
(4) Prior to engine failure testing, it is mandatory that the pilot be fully aware of the
engine, drive system, and rotor limits. These limits were established during previous
ground and flight tests and should be specified in the TIA. Particular attention should be
given to minimum stabilized and minimum transient rotor RPM limits. These values
must be included in the TIA and should be approached gradually with a build-up in time
delay unless the company testing has completely validated all pertinent aspects of
engine failure testing. On category A installations, the maximum power output of each
engine must be limited so that when an engine fails and the remaining engine(s)
Page B – 52
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.