Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
devices to provide or improve longitudinal static stability such as a pitch bias actuator
(PBA), yaw dampers, and fly-by-wire elevator or stabilator surfaces. These systems all
use actuators of some type, and are subject to actuator softover and hardover
malfunctions. The flight control system should be evaluated to determine whether an
actuator jammed in an extreme position would result in reduced control margins.
Generally, if the flight control system stops are between the actuator and the cockpit
control, the control margin will be affected. If the control stops are between the actuator
and the rotor head, the control margins may not be affected, but the location of the
cockpit control may be shifted. This could produce interference with other items in the
cockpit. An example of this would be a lateral actuator jammed hardover causing a
leftward shift in the cyclic stick position. Interference between the cyclic stick, the pilot’s
leg, and the collective pitch control could reduce the left lateral control available and
reduce left sideward flight capability. In the case of fly-by-wire surfaces, both the high
speed forward flight controllability and the rearward flight capabilities could be affected.
Flight control systems that incorporate automatic devices should be thoroughly
evaluated for critical areas. Every failure condition that is questionable should be flight
tested with the appropriate actuator fixed in the critical failure position. These failures
may require limitations of the flight envelope. Any procedure or limitation that must be
observed to compensate for an actuator hardover or softover malfunction should be
included in the Rotorcraft Flight Manual.
b. Procedures.
(1) Flight test instrumentation should include ambient parameters, all flight control
positions, rotor RPM, main and tail rotor flapping (if appropriate), engine power
instruments, and throttle position. Flight controls that are projected to be near their
limits of authority should be rigged to the most adverse production tolerance. A very
accurate weight and balance computation is needed along with a precise knowledge of
the aircraft’s weight and CG variation as fuel is burned.
(2) The critical condition for VNE controllability testing is ordinarily aft CG, MCP, and
minimum power-on rotor RPM, although power and RPM variations should be
specifically evaluated to verify their effects. The turbine engine is sensitive to ambient
temperatures which affect the engine’s ability to produce rated maximum continuous
torque. Flight tests conducted at ambient temperatures that cause the turbine
temperature to limit MCP would not produce the same results obtained at the same
density altitude at colder ambient temperatures where maximum continuous torque
would be limiting. Forward CG should be spot checked for any “tuck under” tendency at
high speed. The VNE controllability test is normally accomplished shortly after the
1.1 VNE (or 1.1VH) point obtained during stability tests required by § 27.175(b).
Controllability must be satisfactory for both conditions. If VNE varies with altitude or
temperature, VNE for existing ambient conditions is utilized for the test. Extremes of the
altitude or temperature envelope should be analyzed and investigated by flight test.
(3) The critical condition for controllability testing in a hover is ordinarily forward CG
at maximum weight with minimum power-on rotor RPM. For rearward flight testing of
Page B - 51
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.