Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
standard sea level conditions to the maximum altitude capability of the rotorcraft or
7,000 feet, whichever is less. On rotorcraft incorporating a tail rotor, efficiency of the tail
rotor decreases with altitude so that a given sideward flight condition requires more
pedal deflection, a higher tail rotor blade angle, and more horsepower. Hence,
directional capability in sideward flight (or at critical wind azimuth) is most critical during
testing at a high altitude site.
(iii) Section 27.143(d) requires adequate controllability when an engine fails. This
requirement specifies conditions under which engine failure testing must be conducted
and includes minimum required delay times.
(A) For rotorcraft that meet the engine isolation requirements of transport
category A, demonstration of sudden complete single-engine failure is required at
critical conditions throughout the flight envelope including hover, takeoff, climb at VY,
and high speed flight up to VNE. Entry conditions for the first engine failure are engine
or transmission limiting maximum continuous power (MCP) (or takeoff power where
appropriate) including reasonable engine torque splits. For multiengine category A
installations (three or more engines) subsequent engine failures should be conducted
utilizing the same criteria as that used for first-engine failure. The applicant may limit
the flight envelope for subsequent failures. Initial or sequential engine failure tests are
ordinarily much less severe than the “last” engine failure test required by § 27.75(b).
The conditions for last-engine failure are MCP, or 30-minute power if that rating is
approved, level flight, and sudden engine failure with the same pilot delay of 1 second
or normal pilot reaction time, whichever is greater.
(B) For rotorcraft without transport category A engine isolation, demonstration of
sudden complete power failure is required at critical conditions throughout the flight
envelope. This includes speeds from zero to VNE (power-on) and conditions of hover,
takeoff, and climb at VY. MCP is specified prior to the failure for the cruise condition.
Power levels appropriate to the maneuver should be used for other conditions. The
corrective action time delay for the cruise failure should be 1-second or normal pilot
reaction time (whichever is greater). Cyclic and directional control motions which are
apart of the pilot task of flight path control are normally not subject to the 1-second
restriction; however, the delay is always applied to the collective control for the cruise
failure. If the aircraft flying qualities and cyclic trim configuration would encourage
routine release of the cyclic control to complete other cockpit tasks during cruise flight,
consideration should be given to also holding cyclic fixed for the 1-second delay.
Although the same philosophy could be extended to the directional controls, the
likelihood of the pilot’s feet being away from the pedals is much lower, unless the
aircraft has a heading hold feature. Rotor speed at execution of the cruise condition
power failure should be the minimum power-on value. The term “cruise” also includes
cruise climb and cruise descent conditions. Normal pilot reaction times are used
elsewhere. Although this requirement specifies MCP, it does not limit engine failure
testing to MCP. If a takeoff power rating is authorized for hover or takeoff, engine
failure testing must also be accomplished for those conditions. Following power failure,
Page B - 49
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.