Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 4 3/31/2014
AC 27.143. § 27.143 (Amendment 27-21) CONTROLLABILITY AND
MANEUVERABILITY.
a. Explanation.
(1) This regulation contains the basic controllability requirements for normal
category rotorcraft. It also specifies a minimum maneuvering capability for required
conditions of flight. The general requirements for control and for maneuverability are
summarized in § 27.143(a) which is largely self-explanatory. During the assessment
carried out under § 27.143(a)(2)(v) for rotorcraft in glide (i.e., autorotation), in addition to
controllability and maneuverability, it should be shown by flight testing that the
directional stability characteristics are sufficient to allow the pilot to control the rotorcraft
without undue attention to heading at the speeds for minimum rate of descent and best
angle of glide. This should be evaluated at normal trim conditions and in turns up to 30°
angle of bank. The ability to generate a sideslip must be evaluated throughout the
autorotation speed envelope. The hover condition is not specifically addressed in
§ 27.143(a)(2) so that the general requirement may remain applicable to all rotorcraft
types, including those without hover capability. For rotorcraft, the hover condition
clearly applies under “any maneuver appropriate to the type.” The rotorcraft must still
meet the stability requirements of Subpart B and, if applicable, Appendix B.
(2) Paragraphs (b) through (e), § 27.143, include more specific flight conditions
and highlight the typical areas of concern during a flight test program.
(i) Section 27.143(b) specifies flight at VNE with critical weight, center of gravity
(CG), rotor RPM, and power. Adequate cyclic authority must remain at VNE for nose-
down pitching of the rotorcraft and for adequate roll control. Nose-down pitching
capability is needed for control of gust response and to allow necessary flight path
changes in a nose-down direction. Roll control is needed for gust response and for
normal maneuvering of the aircraft. In the past, 10 percent control travel margin has
been applied as an appropriate minimum control standard. The required amount of
control power, however, has very little to do with any fixed percentage of remaining
control travel. There are foreseeable designs for which 5 percent remaining is adequate
and others for which 20 percent may not be enough. The key is whether the remaining
longitudinal control travel at VNE generate a clearly positive nose-down pitching moment
and will the remaining lateral travel allow at least 30° banked turns at reasonable roll
rates. Moderate lateral control reversals should be included in this evaluation and since
available roll control can diminish with sideslip, reasonable out of trim conditions
(directionally) should be investigated. This “control remaining” philosophy must also be
applied for other flight conditions specified in this section.
(ii) Section 27.143(c) requires a minimum control capability for hover and takeoff in
winds of 17 knots from any azimuth. Control capability in wind from zero to at least
17 knots must also be shown for any other appropriate maneuver near the ground such
as rolling takeoffs for wheeled rotorcraft. These requirements must be met from
Page B – 48
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.