Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
3/31/2014 AC 27-1B, Chg 4
(4) During the FAA/AUTHORITY flight test program, the crew should be
especially alert for conditions requiring great attentiveness, high skill levels, or
exceptional strength. If any of these features appear marginal, it is advisable to obtain
another pilot’s assessment and to carefully document the results of these evaluations.
Section 27.695 requires an alternate system allowing continued safe flight and landing
following any single failure of a control system hydraulic boost system. This
assessment of ‘safe’ should take into account not only residual post-failure control loads
but also workload and pilot fatigue considerations. The following is suggested as an
appropriate test sequence, conducted by a range of pilots, for a VFR approval:
(i) Simulated hydraulic failure at critical flight conditions and Max GW.
(ii) Establish level flight at a cruise speed >VY.
(iii) Fly for approximately 30 minutes (to assess workload and account for
pilot strength variations), demonstrating ability to climb or descend and small bank
angle turns. This also allows for the possibility that the hydraulic failure occurs over
water or other undesirable landing area.
(iv) Land at a suitable area using a recommended landing technique,
appropriate to the emergency.
(5) Because control loads typically increase at higher altitudes, failure of the
control hydraulic boost system should also be investigated during high altitude testing,
including landing at 7000’ HD, at Max GW/σ. Where approval for any other type of
operation is requested (e.g., IFR, category A), an appropriate test sequence must be
proposed to the FAA/Authority. Section 27.141(b) provides the regulatory requirements
for these strength and skill requirements, as well as a smooth transition capability
between appropriate flight conditions. These requirements must also be met during
appropriate engine failure conditions for each category of rotorcraft. Flight
characteristics and pilot workload should be evaluated in all expected flight conditions,
including actual turbulence.
(6) For night or IFR approval, § 27.141(c) requires additional characteristics for
night and IFR flight. The appropriate flight test procedures are included in other
portions of this guidance.
b. Procedures. None.
Page B - 47
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.