FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 109

PDF page 109 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 109
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B                                                                  9/30/99


                   SUBPART B - FLIGHT

                   FLIGHT CHARACTERISTICS


AC 27.141.  § 27.141 (Amendment 27-21) FLIGHT CHARACTERISTICS-GENERAL.

     a. Explanation.

         (1) This section prescribes the general flight characteristics required for
certification of a normal category rotorcraft. Specifically, it states that the rotorcraft must
comply with the flight characteristics requirements at all approved operating altitudes,
gross weights, center of gravity locations, airspeeds, power, and rotor speed conditions
for which certification is requested. The reference to “altitude” in § 27.141(a)(1) refers
to density altitude. Density altitude is, of course, a function of pressure altitude and
ambient temperature, hence the need to account for ambient temperature effects.
Additional flight characteristics required for instrument flight are contained in Appendix B
of this AC.

         (2) Generally, the aircraft structural (load level) survey accounts for takeoff
power values at speeds up to and including VY. At speeds above VY, maximum
continuous power is assumed. Stress to rotating components usually increases with
airspeed and power.  If the takeoff power rating exceeds the maximum continuous
power rating, and the structural survey has been conducted under the assumption that
takeoff power is not used at speeds above VY, the rotorcraft flight manual (RFM) must
limit takeoff power to speeds of VY and below.  If takeoff power is structurally
substantiated throughout the flight envelope, and appropriate portions of the
controllability, maneuverability, and trim requirements of §§ 27.141 through 27.161 are
met at takeoff power levels, no flight manual entry is needed. Obviously if transmission
limits for maximum continuous (MC) and takeoff power coincide, no special action is
needed.

         (3) During the flight characteristics testing, the controls must be rigged in
accordance with the approved rigging instructions and tolerances. The control system
rigging must be known prior to testing. In addition to the normal rigging procedures, any
programmed control surfaces, which may be operated by dynamic pressure,
electronics, etc., must also be calibrated. During the flight test program, it is frequently
necessary to rig a control, such as the swashplate or tail rotor blade angle, to the
allowable critical extreme of the tolerance band. For example, it would be necessary to
rig the tail rotor to the minimum allowable blade angle if meeting the requirements of
§27.143(c) would be in question. The same consideration must be given to all rotorcraft
controls and movable aerodynamic surfaces where questionable compliance with the
regulations may exist.  If the rotor-induced vibration characteristics of the rotorcraft are
significantly affected and require time-consuming rigging for such things as acceptable
ride comfort, then the rotor(s) should be rigged to the allowable extreme tolerance limits
to determine compliance, for example, with § 27.251.


Page B – 46

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →