Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 1 2/12/03
(MANUAL IDENTIFICATION)
CHAPTER 1
INTRODUCTION (continued)
12. SYMBOLS. Symbols used in the ICA should be listed with explanations in the Introduction
of the ICA.
13. PRECAUTIONS. Precaution means a measure taken beforehand to prevent harm.
a. Any necessary precautions to be taken must be included in the ICA. Reference
Appendix A, A27.3 (b)(3).
b. The following examples of precautions will differ due to the seriousness of the hazard or
condition:
(1) WARNING: Could be a maintenance procedure, practice, condition, etc. that could
result in personal injury or loss of life.
(2) CAUTION: Could be a maintenance procedure, practice, condition, etc. that could
result in damage or destruction of equipment.
(3) NOTE: Could be a maintenance procedure, practice, condition, etc., or a statement
which needs to be highlighted.
14. UNITS OF MEASUREMENT
a. The ICA contains units of measurements. These measurements could be instrument
readings, temperatures, pressures, tolerances, limits, or torque values.
b. It is recommended the ICA contains both United States standard measurements and Metric
measurement, for each measurement, tolerance, or torque value. A general conversion chart is
not acceptable.
15. ICA FOR EACH ENGINE
a. The ICA must include ICA for each engine. Reference Appendix A, A27.1 (b).
b. ICA for type certificated engines are accepted by the FAA/AUTHORITY responsible for
engines and could be included by reference in the applicant’s ICA.
c. ICA for non-type certificated engines are prepared by the applicant and submitted to
appropriate FAA/AUTHORITY for review and evaluation.
16. ICA FOR EACH ROTOR
a. The ICA must include ICA for each rotor. Reference Appendix A, A27.1 (b).
b. ICA for rotors is normally included in the rotorcraft ICA.
17. ICA FOR EACH APPLIANCE REQUIRED BY THIS CHAPTER
a. The ICA must include ICA for each appliance required by FAR/JAR.
Reference Appendix A, A27.1 (b).
REVISION: (PAGE NUMBER)
Revision 4 01-00-00 Page 4
Page Apdx A - 16
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.