FAA / Advisory circular

AC 27-1B

Certification of Normal Category Rotorcraft — Changes 1–9

Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.

Start with the scope.

This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.

The source, within reach.

Search within this AC, jump to a source page, or download the complete saved publication.

Download saved FAA PDF ↓

Read the source

The document, within reach.

FAA source document

PDF page 1026

PDF page 1026 of 1196

Enlarge original ↗

Original FAA page, including its printed amendment and change markings. Extracted words support search; text reflow has not been reviewed.

Original FAA AC 27-1B, PDF page 1026
AC 27-1B · 1026Open saved PDF here ↗
Extracted text for finding words

This extraction supports search. Read the original page for complete notation and layout.

AC 27-1B, Chg 7                                                                       2/4/2016


                (A) IFR. Refer to 14 CFR Appendix B to part 27 and Appendix B of this AC for
information on the IFR requirements for normal category rotorcraft. Per Appendix B to part 27, the
display of information essential for continued safe flight (i.e. attitude, altitude, airspeed, and heading)
must be immediately available to the pilot flying without crewmember action after any single or
combination of failures not shown to be extremely improbable. Automatic reversion displays allows this
required information to be immediately available to the pilot flying without crewmember action. In IFR
designs, it is expected that the first display failure should have no impact on the ability of the pilot to
continue safe IFR flight to the planned destination.

                      (1) For rotorcraft with a certificated dual pilot installation, the copilot’s instruments are
allowed to be used as a standby source of primary information provided they can be used without undue
concentration or fatigue by the pilot. For EDS displays, specific issues, such as the following, should be
addressed:

                                     (i) Pilots should easily see and interpret the displays from their normal seated
position with minimal head movement.

                            (A) The copilot’s systems should be within the pilot’s secondary field of view.

                            (B) The display characteristics should support off-angle viewing in all lighting
conditions.

                                       (ii) Pilots should be able to easily manipulate the displays with one hand from
their normally seated position. Pilot access of the displays and controls must meet the requirements of
§ 27.777 when used by the pilot flying as primary flight information.

                      (2) Automatic reversion allows required information to remain visible to the pilot flying
without crewmember action. The format and arrangement of the reversionary mode is discussed below.

                                     (i) Automatic reversion should provide the required information within one second
of the detected failure of a display or the display’s inability to provide the information.

                                       (ii) Only for an undetectable loss of the display resulting from a backlight failure
or broken display screen is a single button push by the pilot acceptable. The pilot should be able to
recover the lost display of information within one second. However, the design of the display should be
such that these types of failures are extremely improbable.

                (B) VFR. For normal category rotorcraft certificated for VFR only, pilot action to enter a
reversionary mode is acceptable.

                      (1) Pilots should be able to recover the information within one second with a single
action.

                      (2) The reversionary control should be clearly marked and easily identifiable.

                      (3) The reversionary mode must provide all required information in an easily seen
and readable format.

                     (iii) Arrangement. Arrangement of information in a compressed or composite mode must
follow the requirements of § 27.1321 and should follow the guidance in section 27.1321 of this AC as
closely as possible.

                (A) Presentation of primary flight information should remain the same.

                (B) Presentation of navigation information should provide for required information in as
similar a location as possible as a normal display.


Page MG 19 -24

Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.

Aerospace Consulting / Engineering perspective

Start with the certification basis and the function.

Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.

Explore the rotorcraft safety and certification approach →
Source edition and reading coverage

1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.

Source SHA-256: 2dfac16a3644dc18997069cca78746c10726e4b70d3aba996fc87843ffe68a2b

This is a dated source copy. Automatic source acquisition is not yet scheduled.

Original FAA PDF ↗

Working through a certification question?

Bring the aircraft, the basis and the issue your team needs to resolve.

Discuss your programme →