Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
2/4/2016 AC 27-1B, Chg 7
(ii) Within levels of urgency, messages should display in logical order.
(iii) If the length of the information for the message, prompt, or response options
does not display on a single page, there should be an indication that additional message information
exists.
(2) The CAS display should be large enough to generate a display of all possible
warnings that are in a worst-case scenario. The design should provide for sufficient space to display all
possible warnings on the screen at once. To decrease the amount of cascading warnings, use algorithms
to suppress subsequent cascading warnings that would appear because of an event. For example, loss
of an engine could lead to cascading messages of warning-level conditions that resulted from the engine
loss. Unless the pilot has to perform separate procedures to correct subsequent warnings from the
procedures needed to handle the engine loss, there is no need to present them to the pilot.
(3) CAS message priority.
(i) If displaying CAS messages in a window within an EDS display, prioritize how
they will appear. Normally, presentation of warning messages takes precedence over caution and
advisory messages. There can be prioritization of new warnings by importance, recency, or other
prioritization scheme.
(ii) Caution message priority should be defined and easily understood by the
pilot. Scrolling and paging-over to read overflow Caution messages is allowed. The scrolling function
and control must be easily identified and used without undue concentration.
(7) Mission or ancillary displays.
(i) Displays added to the cockpit for specialized uses by a mission crewmember and not the
pilot, such as FLIR displays, should be located outside of the pilot’s secondary field of view, if possible, so
as not to distract the pilot from flying the rotorcraft.
(ii) Displays of non-required information not integrated into an EDS but intended to be used
by the pilot should have all of the attributes and characteristics of an EDS. These displays can be located
within the pilot’s secondary field of view but not in the primary field of view and should not displace the
display of required information.
(A) Display of non-required information should be assessed to ensure it does not provide
misleading information to the pilot or information contrary to that provided by a required source. For
example, an enhanced vision display should not display cues regarding rotorcraft position relative to
hazards or navigation waypoints that are contrary to other information provided on the EDS.
(B) The intended function of a non-required information display should be specific and
defined. For example, “Increase pilot situation awareness” is not an acceptable statement of intended
function. A better statement of intended function is “Increase pilot awareness of hazard location relative
to the rotorcraft.”
(8) Reversionary Modes.
(i) General. Because EDS displays can integrate numerous required flight, powerplant, and
system information into single displays, there is a greater opportunity for a fault to lead to the loss of the
display of multiple parameters. To mitigate this, the use of reversionary modes and displays can ensure
the continued display of required parameters. Reversionary modes are sometimes referred to as
“compressed displays” or “composite displays.”
(ii) Methodology.
Page MG 19 - 23
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.