Certification of Normal Category Rotorcraft — Changes 1–9
Normal category rotorcraft guidance with Changes 1–9 incorporated. Search the complete AC or start with the system safety, flight controls and instrument-flight guidance.
This source includes guidance for different amendments of Part 27. Match the guidance to the aircraft’s agreed certification basis: the 27.1309 entries for Amendments 27-21, 27-46 and 27-51 are separate. The base AC was issued on 30 September 1999; Change 9 is dated 23 June 2023. The FAA catalogue’s 30 September 2008 date is not the date of the latest change.
The source, within reach.
Search within this AC, jump to a source page, or download the complete saved publication.
This extraction supports search. Read the original page for complete notation and layout.
AC 27-1B, Chg 7 2/4/2016
(iv) Markings must follow requirements of §§ 27.1543 through 27.1555.
(2) Graphical and numerical-only displays of parameters or information should follow
the guidance in section d.(1)(ii) above. Providing a numerical readout along with graphically presented
information provides the pilot with complementary data of a specific value coupled with the awareness of
where in the operating range that value resides.
(i) There should be graphical display of powerplant pressures and temperatures,
fuel levels and pressures, and speeds.
(ii) There should also be graphical presentation of other parameters with a range
of normal if the pilot needs to monitor where a parameter is or is changing relative to a limit.
(C) Part-time vs. full-time display of information
(1) Powerplant instruments required by § 27.1305 should be displayed full time (i.e.,
continuous display). However, due to space limitations or display system design, EDS displays that allow
for the de-selection of secondary powerplant instruments (e.g., engine oil temperature and pressure,
transmission oil temperature, electrical information) required by § 27.1305 may be acceptable. There
should be continuous display of primary power information (TQ, MGT, Ng, or their equivalents) and Rotor
tachometer (Nr and Np).
(i) In order to allow the de-selection or part-time display of these parameters,
compensatory features should be designed and provided to alert pilots to select and monitor § 27.1305
instruments prior to the parameter reaching a cautionary or warning limit.
(A) Algorithms and monitoring software can provide the capability to alert
pilots about possible anomalies in a parameter’s behavior. Pilots can then select the appropriate display,
monitor the situation, and mitigate the situation prior to it becoming an abnormal condition.
(B) The monitoring function should automatically provide the same level of
monitoring that would exist if there were continuous display of the individual engine gauges.
(ii) To show compliance using part-time display of § 27.1305 required indicators,
the applicant needs to show equivalence. Coordinate with engine and powerplant specialists since they
will need to assist in the evaluation of the monitoring algorithm parameters. Depending on the strategy
employed, the engine manufacturer may also need to be involved. Additionally, coordinate early with the
FAA since there will need to be an equivalent level of safety.
(ii) System displays. Display of system information (e.g., hydraulic system information,
electrical system information) other than powerplant information may be combined onto an EICAS or IIDS
display or displayed on separate displays.
(A) Crew Alerting System (CAS) and Caution Advisory Warning System (CAWS). EDSs
may include CAS message windows or CAS messages may display on a separate display. CAS
messages must be easily seen and legible in all lighting conditions. The messages or labels must be
easily understandable and use standardized acronyms or labels. Display of CAS messages should be
located as close to the pilot’s central line of vision as possible unless there is a Master Caution or Master
Warning indicator in the pilot’s primary field of view.
(1) Managing Messages and Prompts. The following general guidance applies to all
messages and prompts:
(i) There should be an indication when there are additional messages not
displaying that are in a message queue.
Page MG 19 -22
Saved from the FAA on November 17, 2026. All original pages are retained. Engineering explanations are presented separately below.
Aerospace Consulting / Engineering perspective
Start with the certification basis and the function.
Identify the applicable amendment before selecting the safety guidance. Connect intended functions and operating conditions to failure conditions, architecture decisions, common-cause considerations, verification and limitations. For flight controls and IFR work, carry the relevant 27.672, 27.1329 and Appendix B assumptions into the system safety and compliance evidence.
1196 original pages. 0 pages have reviewed text reflows. Original-first pages retain the source layout, with extracted text available for finding words.
A focused review, an agreed assessment package or ongoing support alongside your team. We can agree the relevant inputs and scope in the initial conversation.
This opens your email application.
Start a conversation
Tell us about your programme, the system you are developing and the support you need.
We can agree a focused use-case review, a defined evidence package or ongoing programme support.
This opens your email application.
Specialist aerospace expertise
Aerospace Consulting is led by Hussein Khimji, an FAA Designated Engineering Representative in systems and equipment, with a focus on system safety, flight controls and avionics.
We work with aircraft developers and systems suppliers to connect technical decisions, safety assessments and certification evidence.
This is the proposed introduction. The full About page will add your approved biography and associate expertise.
Systems engineering & development assurance
Tell us about the aircraft or system, its intended function, stage of development and the support you need.